Adhesives

View our wide range of quality Adhesives, Wood Glues and much more from top brands such as Soudal. Products within this Category include: Fix-ALL® Products; A range of Superior Quality Products based on SMX Technology. Products include Fix-ALL Flexi, Fix-ALL Crystal; Fix-ALL High Tack; Fix-ALL Turbo and Fix-ALL X-Treme Tack. T-Rex® Power Products; Premium Quality Fibre Reinforced High-Grab Adhesives available in... Read More

Adhesives

Soudal Fix All Flexi 290ml Cartridge
Quick Look

Soudal Fix All Flexi

£3.60 ex. VAT | £4.32 inc. VAT

Soudal Fix All Flexi

Soudal Fix All Flexi

Soudal | SMX® Hybrid Polymer

Fix All Flexi (Formerly named Fix All Classic) is a multi-use Sealant, Adhesive and Filler based on SMX® Hybrid Polymer.

Fix All Flexi can be applied in all weather conditions (including wet and damp surfaces), internally and externally.

Fix All Flexi contains no solvents or odours and has primerless adhesion on most construction materials. Overpaintable with most paints.

Non-staining on porous natural stones. Suitable for sanitary applications.

Benefits

Soudal Fix All Flexi

  • Multi-Use Product

  • Stays elastic after curing and very sustainable

  • Excellent adhesion on nearly all surfaces, even if slightly moist.

  • Can be painted with water based systems

  • No odour.

  • Very low emission, EC1 PLUS R certified

  • Impervious to mould, contains ZnP (biocide with fungicidal action)

  • Does not contain solvents, isocyanates, acids, halogens and toxic components, completely neutral.

  • Colourfast.

  • Good colour stability, weather and UV resistance

Application

Typical Applications:

  • For all bonding, sealing and filling applications in all weather conditions, on most surfaces.

  • Paintable and elastomeric sealing and bonding.

  • Bonding and sealing of porous natural stone surfaces such as marble and limestone.

  • Sanitary sealing and bonding - kitchens, bathrooms, showers etc.

Surface Preparation:

Porous surfaces in water loaded applications should be primed with Soudal Primer 150.

Smooth surfaces should be degreased before bonding them together. We recommend a preliminary adhesion test on every surface.

Fix-All® Flexi has an excellent adhesion on most common substrates: All usual building substrates, natural stone, treated wood, PVC, plastics.

Fix All® Flexi has been tested on the following metal surfaces: Steel, AlMgSi1, brass, electrolytic galvanised steel, AlCuMg1, flame galvanised steel, AlMg3 and steel ST1403.

Fix All® Flexi also has a good adhesion on plastics: Polystyrene, polycarbonate (Makrolon®), PVC, ABS, polyamide, PMMA, fiberglass reinforced epoxy, polyester.

While producing plastics very often releasing agents, processing aids and other protective agents (like protection foil) are used. These should be removed prior to bonding.

NOTE: Bonding plastics like PMMA (e.g. Plexi® glass), polycarbonate (e.g. Makrolon® or Lexan®) in stress loaded applications can give rise to stress cracking and crazing in these substrates. The use of Fix All® Flexi is not recommended in these applications.

There is no adhesion on PE, PP, PTFE (Teflon®) and bituminous substrates. We recommend a preliminary compatibility test.

Application Method:

  • Application: With manual or pneumatic Caulking Gun.

  • Cleaning: With Sealant Remover immediately after use.

  • Finishing: With a soapy solution or Soudal Finishing Solution before skinning.

  • Repair: With the same material

Joint Dimensions:

  • Minimum Width for Bonding: 2 mm

  • Minimum Width for Joints: 5 mm

  • Maximum Width for Bonding: 10 mm

  • Maximum Width for Joints: 30 mm

  • Minimum Depth for Joints: 5 mm

  • Recommendation Sealing Jobs: Joint Width = 2 x Joint Depth

Remarks:

  • Fix All® Flexi may be overpainted with water based paints, however due to the large number of paints and varnishes available we strongly suggest a compatibility test before application.

  • The drying time of alkyd resin based paints may increase.

  • Fix All® Flexi can be applied to a wide variety of substrates. Due to the fact that specific substrates such as plastics, like polycarbonate etc... may differ from manufacturer to manufacturer, we recommend preliminary compatibility test.

  • Fix All® Flexi can not be used as a glazing sealant.

  • Not suitable for bonding aquariums.

  • Fix All® Flexi can be used for adhering of and sealing on natural stone.

  • When applying, make sure not to spill any sealant on the surface of materials.

  • The sanitary formula should not replace regular cleaning of the joint. Excessive contamination, deposits or soap remainings will stimulate the development of fungi.

  • A total absence of UV can cause a colour change of the sealant.

Data Sheets

Technical Data Sheet

Fix-All® Product Selector

Safety Data Sheet

£3.60 ex. VAT | £4.32 inc. VAT

Soudal Fix All Crystal Clear - 290ml Cartridge
Quick Look

Soudal Fix All Crystal Clear

£4.15 ex. VAT | £4.98 inc. VAT

Soudal Fix All Crystal Clear

Soudal Fix All Crystal Clear

Soudal | SMX® Hybrid Polymer

Soudal Fix All Crystal Clear is a Super Clear multi-use Sealant, Adhesive and Filler based on SMX® Hybrid Polymer.

Fix All Crystal Clear can be applied in all weather conditions (including wet and damp surfaces), internally and externally.

Fix All Crystal Clear contains no solvents or odours and has primerless adhesion on most construction materials. Overpaintable with most paints.

Non-staining on porous natural stones. Also suitable for sanitary applications.

Benefits

Soudal Fix All Crystal Clear

  • Crystal Clear Formulation

  • Excellent adhesion on nearly all surfaces, even if slightly moist.

  • Very good mechanical characteristics.

  • Impervious to mould, contains ZnP (biocide with fungicidal action).

  • Suitable for Sanitary Applications.

  • Good extrudability even at low temperatures.

  • Free of isocyanates, solvents, halogens and acids.

  • Can be painted with all water based paints and many other systems (to be tested).

  • Permanent elastic after curing.

Application

Typical Applications:

  • All common bonding and sealing applications, both in and outdoor.

  • Transparent and elastic bonding in construction and building applications.

  • Invisible bonding of glass and other transparent materials in indoor applications.

  • Joints in bathrooms and kitchens.

Surface Preparation:

Porous surfaces in water loaded applications should be primed with Soudal Primer 150.

Smooth surfaces should be degreased before bonding them together. We recommend a preliminary adhesion test on every surface.

While producing plastics very often releasing agents, processing aids and other protective agents (like protection foil) are used. These should be removed prior to bonding.

NOTE: Bonding plastics like PMMA (e.g. Plexi® glass), polycarbonate (e.g. Makrolon® or Lexan®) in stress loaded applications can give rise to stress cracking and crazing in these substrates. The use of Fix All® Crystal is not recommended in these applications.

There is no adhesion on PE, PP, PTFE (Teflon®) and bituminous substrates. We recommend a preliminary compatibility test.

Application Method:

  • Application: With manual or pneumatic Caulking Gun.

  • Cleaning: With Sealant Remover immediately after use. Cured Fix-All® can only be removed mechanically.

  • Finishing: With a soapy solution or Soudal Finishing Solution before skinning.

  • Repair: With the same material

Joint Dimensions:

  • Minimum Width for Bonding: 1 mm

  • Minimum Width for Joints: 5 mm

  • Maximum Width for Bonding: 3 mm

  • Maximum Width for Joints: 10 mm

  • Minimum Depth for Joints: 5 mm

Remarks:

  • Fix All® Crystal is paintable with water-based paints, however due to the large number of paints and varnishes available we strongly suggest a compatibility test before application.

  • The drying time of alkyd resin based paints may increase.

  • Fix All® Crystal can be applied to a wide variety of substrates. Due to the fact that specific substrates such as plastics, like polycarbonate, etc, may differ from manufacturer to manufacturer, we recommend preliminary compatibility test.

  • Fix All® Crystal is not suitable for expansion joints.

  • Do not use in applications where continuous water immersion is possible.

  • Fix All® Crystal has a good UV resistance but can discolour under extreme conditions or after very long UV exposure.

  • Fix All® Crystal can not be used as a glazing sealant.

  • Not suitable for bonding aquariums.

  • Fix All® Crystal cannot be used on natural stone. Because the adhesion surface will discolour under influence of the sealant (looks wet) and because this is visible through the crystal clear sealant it seems like staining has occurred.

  • The sanitary formula should not replace regular cleaning of the joint. Excessive contamination, deposits or soap remainings will stimulate the development of fungi.

Data Sheets

Technical Data Sheet

Fix-All® Product Selector

Safety Data Sheet

£4.15 ex. VAT | £4.98 inc. VAT

Soudal Fix All High Tack - 290ml Cartridge
Quick Look

Soudal Fix All High Tack

£4.15 ex. VAT | £4.98 inc. VAT

Soudal Fix All High Tack

Soudal Fix All High Tack

Soudal | SMX® Hybrid Polymer

Fix All High Tack is a Super Strong Sealant, Adhesive and Filler based on SMX® Hybrid Polymer.

Fix All High Tack can be applied in all weather conditions (including wet and damp surfaces), internally and externally.

Fix All High Tack contains no solvents or odours. Primerless adhesion on most construction materials. Overpaintable with most paints.

Fix All High Tack is non-staining on porous natural stones and is suitable for sanitary applications.

Benefits

Soudal Fix All High Tack

  • Super Strong

  • High initial tack reducing the need for initial support.

  • Fast curing

  • Good extrudability

  • High shear strength after full cure (no primer)

  • Stays elastic after curing and very sustainable

  • Impervious to mould, contains ZnP (biocide with fungicidal action)

  • No odour.

  • Can be painted with water based systems

  • Good colour stability, weather and UV resistance

  • Does not contain isocyanates and no silicones

  • Good adhesion on moist substrates

Application

Typical Applications:

  • Sealing and bonding in the building and construction industry.

  • Heavy duty bonding in all weather condition, on most surfaces.

  • Elastic bonding of panels, profiles and other pieces on the most common substrates (wood, MDF, chipboard, etc).

  • Elastic structural bonding in car and container industry.

  • Joints in bathrooms and kitchens.

Surface Preparation:

Porous surfaces in water loaded applications should be primed with Soudal Primer 150.

Smooth surfaces should be degreased before bonding them together. We recommend a preliminary adhesion test on every surface.

While producing plastics very often releasing agents, processing aids and other protective agents (like protection foil) are used. These should be removed prior to bonding.

NOTE: Bonding plastics like PMMA (e.g. Plexi® glass), polycarbonate (e.g. Makrolon® or Lexan®) in stress loaded applications can give rise to stress cracking and crazing in these substrates. The use of Fix All® High Tack is not recommended in these applications.

There is no adhesion on PE, PP, PTFE (Teflon®) and bituminous substrates. We recommend a preliminary compatibility test.

Application Method:

  • Application: With manual or pneumatic Caulking Gun.

  • Cleaning: With Sealant Remover immediately after use. Cured Fix-All® can only be removed mechanically.

  • Finishing: With a soapy solution or Soudal Finishing Solution before skinning. 

  • Repair: With the same material

Joint Dimensions:

  • Minimum Width for Bonding: 2 mm

  • Minimum Width for Joints: 5 mm

  • Maximum Width for Bonding: 10 mm

  • Maximum Width for Joints: 30 mm

  • Minimum Depth for Joints: 5 mm

  • Recommendation Sealing Jobs: Joint Width = 2 x Joint Depth

Remarks:

  • Fix-All® High Tack may be overpainted with water based paints, however due to the large number of paints and varnishes available we strongly suggest a compatibility test before application.

  • The drying time of alkyd resin based paints may increase.

  • Fix-All® High Tack can be applied to a wide variety of substrates. Due to the fact that specific substrates such as plastics, like polycarbonate, etc, may differ from manufacturer to manufacturer, we recommend preliminary compatibility test.

  • While producing plastics very often releasing agents, processing aids and other protective agents (like protection foil) are used. These should be removed prior to bonding. For optimum adhesion the use of Soudal Surface Activator is recommended.

  • Fix-All® High Tack can NOT be used as a glazing sealant.

  • Not suitable for bonding aquariums.

  • Fix-All® High Tack can be used for bonding of natural stone, but it cannot be used as a joint sealant on this type of surface. Fix-All® High Tack can therefore only be used on the bottom of natural stone tiles.

  • When applying, make sure not to spill any sealant on the surface of materials.

  • The sanitary formula should not replace regular cleaning of the joint. Excessive contamination, deposits or soap remainings will stimulate the development of fungi.

Data Sheets

Technical Data Sheet

Fix-All® Product Selector

Declaration of Performance (DoP)

Safety Data Sheet

£4.15 ex. VAT | £4.98 inc. VAT

Soudal Fix All High Tack 'Invisible' - 290ml Cartridge
Quick Look

Soudal Fix All High Tack 'Invisible'

£5.75 ex. VAT | £6.90 inc. VAT

Soudal Fix All High Tack 'Invisible'

Soudal Fix All High Tack 'Invisible'

Soudal | SMX® Hybrid Polymer

Fix All High Tack INVISIBLE is a Super Strong, Super Clear Adhesive with High Initial Tack.

Fix All High Tack Invisible can be applied in all weather conditions, internally and externally.

Fix All High Tack Invisible is virtually odourless with primerless adhesion on most construction materials, including wet and damp surfaces. Can be overpainted with most paints. Non-yellowing and UV Resistant. Very high mechanical properties.

Benefits

Soudal Fix All High Track 'Invisible'

  • High initial tack reducing the need for initial support.

  • Fast curing

  • Good extrudability

  • High shear strength after full cure

  • Stays elastic after curing and very sustainable

  • No odour.

  • Does not contain isocyanates and no silicones

  • Solvent free

  • Good adhesion on slightly moist substrates

Application

Typical Applications:

  • Transparent and elastic bonding in construction and building applications.

  • Elastic bonding of panels, profiles and other pieces on the most common substrates (wood, MDF, chipboard, etc).

Surface Preparation:

Porous surfaces in water loaded applications should be primed with Soudal Primer 150.

Smooth surfaces should be degreased before bonding them together. We recommend a preliminary adhesion test on every surface.

While producing plastics very often releasing agents, processing aids and other protective agents (like protection foil) are used. These should be removed prior to bonding.

NOTE: Bonding plastics like PMMA (e.g. Plexi® glass), polycarbonate (e.g. Makrolon® or Lexan®) in stress loaded applications can give rise to stress cracking and crazing in these substrates. The use of Fix All® High Tack is not recommended in these applications.

There is no adhesion on PE, PP, PTFE (Teflon®) and bituminous substrates. We recommend a preliminary compatibility test.

Application Method:

  • Application: With manual or pneumatic Caulking Gun.

  • Cleaning: With Sealant Remover immediately after use. Cured Fix-All® can only be removed mechanically.

  • Finishing: With a soapy solution or Soudal Finishing Solution before skinning. 

  • Repair: With the same material

Remarks:

  • Fix-All® High Tack Invisible may be overpainted with water based paints, however due to the large number of paints and varnishes available we strongly suggest a compatibility test before application.

  • The drying time of alkyd resin based paints may increase.

  • Fix-All® High Tack Invisible can be applied to a wide variety of substrates. Due to the fact that specific substrates such as plastics, like polycarbonate, etc, may differ from manufacturer to manufacturer, we recommend preliminary compatibilty test.

  • While producing plastics very often releasing agents, processing aids and other protective agents (like protection foil) are used. These should be removed prior to bonding. For optimum adhesion the use of Soudal Surface Activator is recommended.

  • Fix-All® High Tack Invisible cannot be used on natural stone as the adhesion surface will discolour under influence of the sealant (looks wet) and because this is visible through the crystal clear sealant it seems like staining has occurred.

  • Fix-All® High Tack Invisible can not be used as a glazing sealant.

  • Not suitable for bonding aquariums.

  • Fix-All® High Tack Invisible can discolour under extreme conditions or after very long UV exposure.

Data Sheets

Technical Data Sheet

Fix-All® Product Selector

Safety Data Sheet

£5.75 ex. VAT | £6.90 inc. VAT

Soudal Fix All Turbo - 290ml Cartridge
Quick Look

Soudal Fix All Turbo

£5.75 ex. VAT | £6.90 inc. VAT

Soudal Fix All Turbo

Soudal Fix All Turbo

Soudal | SMX® Hybrid Polymer

Soudal Fix All Turbo is a super fast elastomeric adhesive.

Fix All Turbo has rapid strength build up after 20 minutes and final bond strength after 3 hours, high initial tack.

Fix All Turbo can be applied in all weather conditions (including wet and damp surfaces), internally and externally. No solvents or odours. Primerless adhesion on most construction materials.

Benefits

Soudal Fix All Turbo

  • Super fast

  • Rapid strength build up after 20 minutes

  • 3 hours final bond strength

  • Virtually Odourless

  • All Weather Use

  • Primerless adhesion

Application

Typical Applications:

  • For all elastomeric bonding applications where adhesive build up speed is highly critical or important.

  • Heavy duty bonding in all weather conditions, on most surfaces.

  • Bonding and sealing of porous natural stone surfaces such as marble and limestone.

Surface Preparation:

Porous surfaces in water loaded applications should be primed with Soudal Primer 150.

Smooth surfaces should be degreased before bonding them together. We recommend a preliminary adhesion test on every surface.

Fix-All® Turbo has been tested on the following metal surfaces: Steel, AlMgSi1, brass, electrolytic galvanised steel, AlCuMg1, flame galvanised steel, AlMg3 and steel ST1403.

Fix-All® Turbo also has a good adhesion on plastics: Polystyrene, polycarbonate (Makrolon®), PVC, ABS, polyamide, PMMA, fiberglass reinforced epoxy, polyester.

While producing plastics very often releasing agents, processing aids and other protective agents (like protection foil) are used. These should be removed prior to bonding.

NOTE: Bonding plastics like PMMA (e.g. Plexi® glass), polycarbonate (e.g. Makrolon® or Lexan®) in stress loaded applications can give rise to stress cracking and crazing in these substrates. The use of Fix All® Turbo is not recommended in these applications.

There is no adhesion on PE, PP, PTFE (Teflon®) and bituminous substrates. We recommend a preliminary compatibility test.

Application Method:

  • Application: Apply the adhesive by means a caulking gun in uniform adhesive strips or dots (every 15 cm) on one of the substrates. Always apply an adhesive dot or strip on the corner and edges of panels. Bond the substrate and tamp with a rubber hammer. If necessary, support the bonded materials. The adhesive is hand tight after 20min and can be loaded after 3 hours.

  • Cleaning: With Sealant Remover immediately after use. Cured Fix-All® can only be removed mechanically.

  • Finishing: With a soapy solution or Soudal Finishing Solution before skinning. 

  • Repair: With the same material

Remarks:

  • Fix-All® Turbo is paintable with most Water-based paints, however due to the large number of paints and varnishes available we strongly suggest a compatibility test before application.

  • The drying time of alkyd resin based paints may increase.

  • Fix-All® Turbo can not be used as a glazing sealant.

  • Not suitable for bonding aquariums.

  • Fix-All® Turbo can be used for bonding of natural stone, but it cannot be used as a joint sealant on this type of surface. Fix-All® Turbo can therefore only be used on the bottom of natural stone tiles.

  • When applying, make sure not to spill any sealant on the surface of materials.

Data Sheets

Technical Data Sheet

Fix-All® Product Selector

Declaration of Performance (DoP)

Safety Data Sheet

£5.75 ex. VAT | £6.90 inc. VAT

Soudal Fix All X-Treme Power - 290ml Cartridge
Quick Look

Soudal Fix All X-Treme Power

£4.95 ex. VAT | £5.94 inc. VAT

Soudal Fix All X-Treme Power

Soudal Fix All X-Treme Power

Soudal | SMX® Hybrid Polymer

Soudal Fix All X-Treme Power is an Extreme Tack, high strength elastomeric adhesive with enhanced mechanical properties.

With its ultimate initial grab, Fix All X-Treme Power can be applied in all weather conditions (including wet and damp surfaces), internally and externally. No solvents or odours. Soudal Fix All X-Treme Power offers primerless adhesion on most construction materials.

Benefits

Soudal Fix All X-Treme Power

  • Extreme Tack

  • Ultimate Initial Grab

  • Very High Final Mechanical Properties

  • Easily Gunnable

  • Primerless Adhesion

  • Virtually Odourless

  • All Weather Use

  • Isocyanate and silicone free.

Application

Typical Applications:

  • For all bonding applications where a high initial grab and final bond is extremely important.

  • Heavy Duty bonding in all weather conditions, on most surfaces.

  • Bonding and sealing of porous natural stone surfaces such as marble and limestone.

Surface Preparation:

Porous surfaces in water loaded applications should be primed with Soudal Primer 150.

Smooth surfaces should be degreased before bonding them together. We recommend a preliminary adhesion test on every surface.

Porous surfaces in water loaded applications should be primed with Soudal Primer 150. All smooth surfaces can be treated with Soudal Surface Activator.

Fix ALL X-Treme Power has excellent adhesion on most substrates. Fix-All® X-Treme Power is has been tested on following metal surfaces: stainless steel, AlMgSi1, brass, electro-galvanized steel, AlCuMg1, hot dip galvanized steel, AlMg3, steel ST1403.

Fix-All® X-Treme Power also has a good adhesion on plastics: polystyrene, PVC, polyamide, fiberglass reinforced epoxy, polyester. While producing plastics very often releasing agents, processing aids and other protective agents (like protection foil) are used. These should be removed prior to bonding. For optimum adhesion the use of Soudal Surface Activator is recommended.

NOTE: Bonding plastics like PMMA (e.g. Plexi® glass), polycarbonate (e.g. Makrolon® or Lexan®) in stress loaded applications can give rise to stress cracking and crazing in these substrates. The use of Fix-All® X-Treme Power is not recommended in these applications.

There is no adhesion on PE, PP, PTFE (Teflon®) and bituminous substrates. We recommend a preliminary compatibility test.

Application Method:

  • Application: Apply the adhesive with a caulking gun onto one surface in beads or dabs (every 15cm). Always apply adhesive to the edges and corners of panels. Press the surfaces together and batten down with a rubber hammer. Support of the bonded materials may be required. The bond can be fully loaded after 24-48 hours.

  • Cleaning: With Sealant Remover immediately after use. Cured Fix-All® can only be removed mechanically.

  • Finishing: With a soapy solution or Soudal Finishing Solution before skinning. 

  • Repair: With the same material

Remarks:

  • Fix All® X-Treme Power is paintable with most water-based paints, however due to the large number of paints and varnishes available we strongly suggest a compatibility test before application.

  • The drying time of alkyd resin based paints may increase.

  • Fix All® X-Treme Power can be applied to a wide variety of substrates. Due to the fact that specific substrates such as plastics, like polycarbonate, etc, may differ from manufacturer to manufacturer, we recommend preliminary compatibility test.

  • Fix All® X-Treme Power can not be used as a glazing sealant.

  • Not suitable for bonding aquariums.

  • Fix All® X-Treme Power can be used for bonding of natural stone, but it cannot be used as a joint sealant on this type of surface. Fix All® X-Treme Power can therefore only be used on the bottom of natural stone tiles.

  • When applying, make sure not to spill any sealant on the surface of materials.

Data Sheets

Technical Data Sheet

Fix-All® Product Selector

£4.95 ex. VAT | £5.94 inc. VAT

G B Pro Crystal Clear Hybrid Sealant & Adhesive - C3 Cartridge
Quick Look

G B Pro Hybrid Sealant & Adhesive

£2.95 ex. VAT | £3.54 inc. VAT

G B Pro Hybrid Sealant & Adhesive

G B Pro Hybrid Sealant & Adhesive

Bond-It | Adhesives & Wood Glues

Grab Adhesives

G B Pro is a one part, high quality, high modulus sealing and bonding material based on advanced hybrid polymer technology.

G B Pro is a totally neutral 'hybrid' sealant for use in areas requiring a tough elastic rubber joint or as an adhesive with superior bonding strength. 

G B Pro Conforms to ISO11600-F&G-20HM.

G B Pro is available in White or Crystal Clear colours.

Benefits
  • High modulus, remains permanently flexible.

  • For sealing and bonding interior and exterior applications in all weather conditions.

  • Can be over-painted.

  • Non shrinking.

  • Contains no isocyanates, solvents, silicone and phthalates.

  • Rapid curing.

  • Excellent adhesion to most surfaces (even moist surfaces).

  • Wet on wet application.

  • No odour.

Product Uses

G B Pro can be used for the following:

  • For filling and sealing of connecting joints, cracks, holes, etc in the building sector.

  • For bonding metal to metal (can absorb vibration).

  • As a universal waterproof construction adhesive for bonding concrete, mirrors (note: not suitable for plastic backed/safety mirrors), gypsum board, polycarbonates, polystyrene, PVC, many plastics, ceramics, copper, lead, zinc, aluminium, stainless steel, wood and glass.

We recommend that test areas be carried out prior to application to ensure compatibility of materials.

Application

Preparation:

Ensure all surfaces are clean and free from grease, oil or any other contaminants that may hinder adhesion.

Application Method:

Carefully cut the top of the cartridge taking care not to damage the threaded area.

Screw on the nozzle supplied and cut at an angle approximately 45°.

Apply using a standard sealant gun.

  • As an Adhesive: Apply in beads or strips and bond the surfaces together carefully and allow to cure.

  • As a Sealant: Apply in a continuous bead along the aperture and leave to fully cure. Smooth the joint by tooling with a soapy solution. Remove any excess material and clean tools immediately with white spirit. Replace plastic cap after use.

Limitations:

Please note this product is not recommended for use with expansion joints or for installations where the joints are continually immersed in water.

If allowed to cure in dark conditions or poor light the product may yellow.

This product is not suitable for use in aquariums.

Not suitable for use on LSE plastics such as PE, PP and PTFE.

This product may cause staining on marble and other stone surfaces.

This can be avoided by using a sealer prior to application of G B Pro.

Do not use for bedding in double glazed units, for this application we would recommend using Silirub® 2.

Do not use on surfaces that bleed oils or plasticisers.

Paintability: As quality and type of paint can vary, always test compatibility before use.

Any mirror made with 6mm glass or thicker needs mechanical fixing.

Any mirror on a sloping wall or ceiling must have mechanical fixings.

Any mirror greater than 1m² must have mechanical fixings.

Data Sheets

Technical Data Sheet

Safety Data Sheet (White)

Safety Data Sheet (Crystal Clear)

£2.95 ex. VAT | £3.54 inc. VAT

Soudaseal® Mirror - Hybrid Polymer Mirror Adhesive
Quick Look

Soudaseal® Mirror - Hybrid Polymer Mirror Adhesive

£5.49 ex. VAT | £6.59 inc. VAT

Soudaseal® Mirror - Hybrid Polymer Mirror Adhesive

Soudaseal® Mirror - Hybrid Polymer Mirror Adhesive

Soudal | Mirror Adhesive

Soudaseal® Mirror is a Hybrid Polymer based Mirror Adhesive and Sealant which has a high bond strength and fast cure on to nearly all surfaces, even when damp.

Soudaseal® Mirror has high performance mechanical properties and excellent extrudability, even at low temperatures.

Soudaseal® Mirror is free of isocyanates, silicone, solvents and acids meaning health and safety considerations are minimal.

Soudaseal® Mirror is resistant to many chemicals and withstands mould growth. There is also no staining of porous materials such as natural stone, blue stone, marble and granite when applying Soudaseal® Mirror.

Soudaseal® Mirror is compatible with all acetone resistant mirrors.

Benefits
  • Hybrid Polymer Sealant & Adhesive

  • Fast Curing

  • Primerless adhesion even on damp surfaces due to unique adhesion promoters.

  • Stays elastic after curing and very sustainable.

  • No odour and does not contain solvents.

  • Does not contain isocyanates and no silicones.

  • No risk for staining on porous substrates (migration of plasticizer).

  • Colourfast.

Application

Typical Applications:

  • Sealing and bonding of mirrors on to most types of surfaces.

  • Sealing of joints in mirror walls.

  • Bonding of mirrors even on damp surfaces.

  • Water resistant bonding.

Surface Preparation:

Surfaces should be clean, dry, free of dust and grease.

Porous surfaces in water loaded applications should be primed with Soudal Primer 150. All smooth surfaces can be treated with a Surface Activator.

Soudaseal® Mirror has excellent adhesion on most substrates. Soudaseal® Mirror can also be used on natural stone.

There is no adhesion on PE, PP, PTFE (Teflon®) and bituminous substrates. We recommend a preliminary compatibility test.

Application Method:

  • Application Method: With a manual or pneumatic caulking gun. Apply Soudaseal® Mirror with attached V-cut nozzle in vertical adhesive beads on the back of the mirror. Depending on the weight of the mirror an adhesive bead shall be applied every 10 to 20cm.

  • Cleaning: Clean with a Sealant Remover.

  • Finishing: With a soapy solution or Soudal Finishing Solution before skinning.

  • Repair: With the same material

Remarks:

  • Due to the wide variety of types of mirrors, we strongly recommend preliminary compatibility tests.

  • Due to the low initial tack, the mirrors need to be supported during the curing process until the adhesive has fully cured. The time required depends on the weight / size of the mirror, temperature, relative humidity and the amount of product used.

  • In order to avoid possible problems due to condensation, the mirror manufacturers as well as Soudal recommend sufficient ventilation at the back of the mirror. As a guideline, an opening of 3-4mm should be left between the surface and the mirror. This can be assured by the use of double sided mirror tape.

  • We recommend this minimal ventilation opening of 3-4mm to ensure correct curing of the adhesive / sealant. Full surface bonding is at own risk of the applicator.

  • For larger mirrors always use the adhesive in combination with a very good and qualitative double-sided adhesive mirror tape.

  • Mirrors that are fitted with a safety film at the back to avoid shattering must be pre-treated with an adhesion promoter. The use of Soudal Surface Activator will ensure the best bonding performance on this type of safety film. Without the use of Soudal Surface Activator the adhesive bond might be insufficient with the risk of an unsafe situation.

Data Sheets

Technical Data Sheet

Declaration of Performance (DoP)

Safety Data Sheet

£5.49 ex. VAT | £6.59 inc. VAT

Soudabond Easy - PU Adhesive Foam
Quick Look

Soudabond Easy - PU Adhesive Foam

£6.95 ex. VAT | £8.34 inc. VAT

Soudabond Easy - PU Adhesive Foam

Soudabond Easy - PU Adhesive Foam

Soudal | PU Adhesive Foam

Soudal Soudabond Easy is a Fast Curing, Ready-to-use, self-expanding polyurethane adhesive for clean, efficient and economical permanent bonding of insulation panels, plasterboard and many other building and construction materials.

Benefits
  • Cuts working time by up to 30%.

  • Excellent initial bond, even at low temperatures.

  • Economical in use due to precise application.

  • One can of 'Gun Grade' covers up to 14m² of insulation. 'Hand Held' and 'Genius Gun®' Applications cover up to 12m²

  • Suitable for vertical applications.

  • Can be applied at temperatures between -5°C and +35°C.

  • Thermal conductivity 0.035 W/m.K enhances performance of insulation panels when filling gaps.

  • Remains flexible, does not become brittle.

  • Levels uneven surfaces.

  • Limited post expansion for fast and precise installation of insulation panels and plasterboard.

  • Substantial space and weight savings compared to conventional PU roof adhesives, bonding mortars, etc.

  • Fast curing, work can continue about 1 hour after application.

  • Solvent-Free.

  • Resistant to a variety of solvents, paints and chemicals.

  • Does not age or rot, mould and mildew resistant, but not UV resistant.

  • Water resistant (not watertight).

  • Building material class B2 according to DIN 4102, Part 1.

Product Uses

Typical Applications:

  • Clean, efficient and economical permanent bonding of insulation panels.

  • Suitable for Bonding Polystyrene (EPS + XPS), polyurethane (PUR/PIR) and phenol resin foam based insulation panels for flat roofs, perimeters, facades, insulation/drain elements, cellar ceilings, internal insulation, etc.

  • Suitable for Bonding Gypsum Plasterboard / Gypsum Fiberboard in Dry Lining applications.

  • Suitable for Bonding non-load Bearing Walls; e.g. Partition Walls, Screen Walls, Cellar Bars, Stone Shelves, etc., of Concrete Precision Blocks (Aerated Concrete, Sand-lime Brick, Gypsum,...).

  • Fills cavities between individual thermal insulation panels.

Substrates:

All usual substrates such as concrete, masonry, stone, plaster, wood, cold bituminous thick coatings, sand or slate surfaced bituminous sheeting, polystyrene, polyurethane and phenol resin foam, corrosion protected steel sheeting, fibre cement, gas concrete, particle board, plasterboard, gypsum fiberboard, fibre cement, hard PVC and emulsion paints.

Adhesive surfaces must be stable, clean, without bubbles and free of separating agents such as talcum, grease, oils, etc. Suitable on moist, but not wet (water film, standing water) substrates. Any cement slurries and sinter layers on mineral substrates must be removed mechanically. Bubbles in bituminous sheeting must be removed. To ensure perfect adhesion, the bituminous sheeting should have a fully covered surface.

Does not adhere to PE, PP. PTFE and silicone. All substrates should be tested for suitability with regard to adhesion and compatibility.

Videos:

Soudabond Easy Tutorial:

How to bond Cellular Concrete with Soudabond Easy:

Application

General - Gun Grade Application:

Prior to using the product, cover all adjacent areas for protection against soiling.

In windy conditions, precautions must be taken to ensure that Soudabond Easy cannot contaminate components, objects or persons in the vicinity.

Good ventilation must be ensured for indoor use. Wear protective goggles and gloves.

Tightly screw the can to the thread in the gun and shake the gun about 20 times downwards so that the contents are mixed well to ensure an optimum adhesive quality and high yield.

After extended periods of non-use, the Applicator gun must be shaken again to obtain the required adhesive quality! With the adjusting screw on the gun, adjust the adhesive bead to the required diameter. (The emptier the can, the more the adjusting screw needs to be opened). The gun must be held vertical during application.

A distance of 1 to 2 cm must be maintained between the gun nozzle and insulation panel/substrate while spraying. Apply pressure to the insulation panel within about 8 minutes (20°C - 65% R.H. – this time is shorter at higher temperature / humidity and longer at lower temperature / humidity).

Do not tap or remove and reapply panels as this will damage the adhesive structure and reduce the adhesive strength substantially.

At high temperatures and low humidity in particular, curing can be accelerated by lightly spraying the adhesive bead with water.

General - Hand Held Application:

Follow the same preparation measures as above. Screw the straw to
valve and shake the can about 20 times downwards so that the contents are mixed well to ensure an optimum adhesive quality and high yield.

After extended periods of non-use, the can must be shaken again to obtain the required adhesive quality! The can must be held vertical during application.

A distance of 1 to 2 cm must be maintained between the straw nozzle and insulation panel / substrate while spraying.

Apply product as mentioned above.

Bonding Flat Roof Insulation Materials:

Apply Soudabond Easy directly to the substrate. Pressure should be applied to the insulation panels for optimal contact and maintained using suitable weights for at least 15 minutes to prevent lifting and slipping through wind suction. The panels must not be subjected to traffic for about 2 hours.

Consumption: At least three uniform adhesive beads with a minimum diameter of 30 mm are required per m² adhesive surface. The number of adhesive strips, according to DIN 1055, part 4, depend on the region, roof area, structure height, corner and edge areas as well as the materials to be bonded.

The amount of adhesive to be applied depends on the wind load and must be increased in corner and edge areas.

Perimeter Insulation:

Soudabond Easy facilitates the installation of insulation panels in perimeter areas according to DIN 4108-2. (Not suitable for pressing water!).

Spray Soudabond Easy from bottom to top with a bead spacing of about 25 cm (minimum three beads per continuous panel or minimum two beads for short panels!) on to the insulation panel or cellar wall.

Press the insulation panel lightly against the cellar wall. Work from bottom to top without gap.

The insulation panels must be bonded staggered in corners of buildings. The installed insulation panels can be readjusted with a long spirit level to correct any post expansion of the adhesive within 8 minutes.

The insulation achieves its final strength through the pressure of the filled soil, gravel or similar. Filling must take place within 14 days after bonding.

In all other cases, Soudabond Easy is ideal for bonding insulation panels to interior walls and exterior facades!

The can must be held vertical during application. Apply a circular bead of Soudabond Easy to the insulation panel with enclosed M/W to cover an adhesive area of minimum 40% with pressure applied.

Wait at least 2 to maximum 8 minutes (20°C / 65% R.H. – this time is shorter at higher temperature / humidity and longer at lower temperature/humidity) and subsequently press the insulation panel against the wall.

Work from bottom to top without gap. Insulation panels must be bonded staggered in outer corners of buildings. Installed insulation panels can be adjusted with a long spirit level after 10 to 15 minutes to correct any post expansion of the adhesive.

It is recommended to fix the last installed insulation panel during breaks

Cellar Ceiling Insulation:

For working overhead, suitable protective goggles must be worn!

Soudabond Easy has a very high initial bonding strength and is therefore ideal for permanent bonding of insulation panels to cellar ceilings, garage ceilings or other overhead areas, also without additional mechanical fastening.

Suitable are all standard insulation panels of polystyrene (EPS and XPS) and PUR/PIR measuring 500 x 500 mm with a maximum thickness of 100mm and a maximum weight of 400g.

Larger and heavier insulation panels and/or additional surfaces should be fixed mechanically within 15 minutes. This is easily done using ceiling supports for example.

Prior to application, the substrate stability must be verified. This can also take place with a sealing tape test.

In this test, sealing tape is applied to the substrate and quickly pulled off again. If old paint or plaster adheres to the adhesive tape, this means that the substrate does not have the necessary stability and must be reinforced or removed. With chalking and highly absorbent substrates, the substrate adhesion can be improved with a deep solvent primer. Protruding concrete burr must be removed mechanically.

At least one circular and one angular adhesive foam bead with a minimum diameter of 30mm (about 40g per panel) must be applied to each 500mm x 500mm panel.

Do not apply the adhesive too close to the outer edges to avoid the excess going over the edges when pressure is applied to the insulation panel.

Before bonding the insulation panel to the ceiling, Soudabond Easy must be allowed to stand for 3 to maximum 6 minutes to achieve the required initial strength.

The insulation panel can subsequently be bonded to the ceiling. The panel must be placed carefully in the required position and pressure applied without tapping (damages the adhesive structure).

The next insulation panel must be bonded 5 minutes after the previously bonded panel so that it remains in place when the next panel is bonded.

Insulation panels must be additionally fixed in the centre with a suitable insulation anchor under unfavourable bonding conditions.

Interior Insulation / Dry Lining:

Prior to application, the substrate stability must be verified. This can also take place with a sealing tape test. In this test, sealing tape is applied to the substrate and quickly pulled off again. If old paint or plaster adheres to the adhesive tape, this means that the substrate does not have the necessary stability and must be reinforced or removed.

With chalking and highly absorbent substrates, the substrate adhesion can be improved with a deep solvent primer.

Remove protruding concrete burr or excess plaster. Soudabond Easy levels uneven surfaces up to 30mm.

Interior Insulation Panels:

Apply Soudabond Easy about 2cm away from the edge of the panel as a 30mm circular bead and to the panel surface in lines or a W-shape. It must be ensured that the adhesive contact area is about 40% after applying pressure.

The adhesive must always be applied circular also for panel cut-outs, penetrations, etc., to prevent rear circulation of the interior insulation.

After applying Soudabond Easy, depending on the climatic conditions, allow to flash off for about 3-6 minutes. This ensures that an optimal adhesive strength is achieved with reduced post expansion. Subsequently place the insulation panel on wedges, align and apply pressure from bottom to top. Do not tap or remove the panels as this can reduce the adhesive strength substantially.

Apply new adhesive if necessary. After about 6 to 10 minutes, check for correct seating, readjust with a spirit level/level. Edges of walls, ceilings and floors, openings and penetrations must be filled out completely with Soudabond Easy air-tight and sound insulated. Work can be continued after minimum 1 hour.

Soudabond Easy can also be used for mounting electrical installation boxes.

Plasterboard:

In contrast to interior installation, three vertical adhesive beads are sufficient for the installation of plasterboard wider than 50cm. For panel widths below 50cm, a minimum of two adhesive beads must be applied.

Concrete Precision Block Bonding:

Soudabond Easy must not be used for components requiring approval, e.g. supporting walls and walls relevant for safety!  Good ventilation must be ensured for indoor use.

Clean the adhesive surfaces, remove lose particles and moisten. Apply two Soudabond Easy adhesive beads with a diameter of about 30mm to the substrate and subsequently to all further concrete precision blocks.

The adhesive beads must be applied about 50mm away from the stone edge parallel on horizontal and vertical joints.

Position / join and align bricks within minimum 2 to maximum 8 minutes (20°C/65% R.H. – this time is shorter at higher temperature/humidity and longer at lower temperature / humidity).

If once joined bricks are removed, new adhesive beads must be applied. Allow excess adhesive to cure and subsequently remove, e.g. with a spatula.

Depending on the ambient temperature, work can be continued after minimum 60 minutes. The adhesive achieves full strength after minimum 12 hours.

Other Applications:

Due to its excellent adhesive properties, reduced foaming and fast final strength, Soudabond Easy is suitable for numerous bonding applications.

Soudabond Easy is ideal for the installation of insulation panels in building and construction. Installation of loft insulation reveals and claddings as well as bonding of wall edging strips are just a few examples.

General Note:

Do not load/subject the bond to traffic within the curing time of about 2 hours! All open joints within the insulation can be filled out with Soudabond Easy.

Trim protruding, fully cured adhesive with a sharp knife.

Soudabond Easy can be painted or plastered after curing.

Data Sheets

Soudabond Easy Application Manual

Technical Data Sheet - Gun Grade

Technical Data Sheet - Hand Held

Technical Data Sheet - Genius Gun®

Safety Data Sheet

£6.95 ex. VAT | £8.34 inc. VAT

Pro 45P - Fast Set D4 Polyurethane Adhesive
Quick Look

Pro 45P - Fast Set D4 Polyurethane Adhesive

£5.65 ex. VAT | £6.78 inc. VAT

Pro 45P - Fast Set D4 Polyurethane Adhesive

Pro 45P - Fast Set D4 Polyurethane Adhesive

Soudal | Polyurethane Adhesive

Soudal Pro 45P is a premium grade, ultra fast setting liquid Polyurethane Adhesive with excellent water resistance and easy application.

Soudal Pro 45P is water resistant, D4 Strength (DIN EN 204) adhesion with a 5 minute open time and can be used on damp surfaces.

Superior bonding strength with foaming penetration action to fill any bond cavities.

Benefits
  • Professional Quality

  • Easy Application

  • Very Fast Drying Time

  • Foaming Penetration Action to Fill Bond Cavities

  • Powerful Bond Strength

  • Water Resistance: D4 (DIN EN 204)

  • Can be used on Humid Wood

Application

Typical Applications:

Soudal Pro 45P is used for interior and exterior applications, it can withstand frequent long term exposure to running or condensed water and exterior applications with exposure to weather influences.

Soudal Pro 45P can also be used for the manufacturing of door and window frames that need to meet class D4 according to EN204 and can also be used for heavy duty bonding of wooden construction elements.

Suitable for use on various porous and non-porous substrates such as concrete, bricks and many other common materials in the building industry.

Surface Preparation:

Surfaces should be clean, dry, free of dust and grease.

Slight moistening of surfaces improves curing rate and gap filling characteristics as adhesive foams up to penetrate cavities.

We recommend a preliminary adhesion test on every surface.

Application Method:

  • Application Method: Apply adhesive with a brush or an adhesive comb, join the parts and compress for approximately 60-90 minutes.

  • Cleaning: With White Spirit or Acetone.

  • Repair: With the same material

Data Sheets

Technical Data Sheet

Safety Data Sheet

£5.65 ex. VAT | £6.78 inc. VAT

PU Construct - Rapid Set D4 Polyurethane Adhesive - 310ml Cartridge
Quick Look

PU Construct - Rapid Set D4 Polyurethane Adhesive

£4.10 ex. VAT | £4.92 inc. VAT

PU Construct - Rapid Set D4 Polyurethane Adhesive

PU Construct - Rapid Set D4 Polyurethane Adhesive

Soudal | Polyurethane Adhesive

Soudal PU Construct is a one component Rapid Setting, gun applied, thixotropic polyurethane based construction adhesive with high bond strength and high water resistance.

Soudal PU Construct cures under the influence of humidity. Slight moistening of substrates improves curing rate and gap filling characteristics as adhesive foams up to penetrate the bond cavity.

Soudal PU Construct has a 15 minute pressing time and is fully cured in 30 minutes.

Benefits
  • Conforms to DIN EN 204 Grade D4

  • Professional Wuality

  • Cartridge Applied

  • Fast Curing and Strength Build-up

  • Filling Characteristics, Suitable for Uneven Surfaces

  • Clamping Increases the Bonding Strength

  • Waterproof D4

  • For Indoor and Outdoor Use

  • Solvent-Free

Application

Typical Applications:

  • General joinery of wooden materials.

  • Manufacturing of door and window frames that need to match class D4 according to EN204.

  • For heavy duty bonding of wooden construction elements

  • Bonding of insulation materials (including polystyrene).

  • Can be used on porous and non porous construction materials, i.e bricks and concrete.

  • Surface Type: Various porous and non-porous substrates such as wood, concrete, bricks and other common materials in the building industry. Not suitable for PE and PP.

Surface Preparation:

Surfaces should be clean, dry, free of dust and grease.

The adhesive cures under the influence of humidity. Slight moistening of substrates improves curing rate and gap filling characteristics as adhesive foams up to penetrate the bond cavity.

We recommend a preliminary adhesion test on every surface.

Application Method:

  • Application Method: Slightly moisten both substrates. Apply the adhesive by means of a manual or pneumatic caulking gun to one of the substrates. Join the parts together within 5 minutes and clamp for at least 15 minutes. Pressing the materials, during curing, is necessary to reach the highest possible end strength. PU Construct reaches 80% of its end strength after 10min (when moistened). When bonding 2 non-porous substrates, moisten only one of the two substrates. Avoid displacing of the substrates during joining both substrates together or during the curing process.

  • Cleaning: PU Construct can, before the adhesive is cured, be removed from tools and materials with Soudal Gun and Foam Cleaner. Cured adhesive has to be removed mechanically.

  • Repair: With the same material

Remarks:

  • Not suited for applications with continuous water immersion.

Data Sheets

Technical Data Sheet

Safety Data Sheet

£4.10 ex. VAT | £4.92 inc. VAT

Purocol Express - Fast Set D4 Polyurethane Adhesive - 310ml Cartridge
Quick Look

Purocol Express - Fast Set D4 Polyurethane Adhesive

£4.10 ex. VAT | £4.92 inc. VAT

Purocol Express - Fast Set D4 Polyurethane Adhesive

Purocol Express - Fast Set D4 Polyurethane Adhesive

Soudal | Polyurethane Adhesive

Soudal Purocol Express is a one component, fast setting, gun applied, thixotropic, polyurethane based construction adhesive.

Soudal Purocol Express is a professional quality product with extra fast curing and gap filling characteristics, suitable for uneven surfaces.

Soudal Purocol Express conforms to DIN EN 204 D4.

Soudal Purocol Express is solvent free and waterproof with a 5 minute open time and 1 hour pressing time.

Benefits
  • Conforms to DIN EN 204 Grade D4

  • Foaming Action to Fill Gaps

  • Transparent

  • 5 Minute Open Time

  • 1 Hour Pressing Time

  • Solvent Free

Application

Typical Applications:

  • For interior applications with frequent exposure to condensed or running water.

  • Exterior applications with exposure to weather influences.

  • Manufacturing of door and window frames that need to match class D4 according to EN204.

  • For heavy duty bonding of wooden construction elements.

  • Can be used on porous and non porous construction materials, i.e bricks and concrete.

  • General Joinery of wooden materials.

Surface Preparation:

Surfaces should be clean, dry, free of dust and grease.

The adhesive cures under the influence of humidity. Slight moistening of substrates improves curing rate and gap filling characteristics as adhesive foams up to penetrate the bond cavity.

We recommend a preliminary adhesion test on every surface.

Application Method:

  • Application Method: Apply the adhesive by means of a manual or pneumatic caulking gun to one of the to be bonded materials. Join the parts together within 5 minutes and clamp for at least 1 hour. Pressing the materials, during curing, is necessary to reach the highest possible end strength.

  • Cleaning: Purocol Express can, before the adhesive is cured, be removed from tools and materials with Soudal Gun and Foam Cleaner. Cured adhesive has to be removed mechanically

  • Repair: With the same material

Remarks:

  • Not suited for applications with continuous water immersion.

Data Sheets

Technical Data Sheet

Safety Data Sheet

£4.10 ex. VAT | £4.92 inc. VAT