Search
Account
Cart
Menu
Soudal | SMX® Hybrid Polymer
Soudal Fix All Turbo is a Premium Quality, Super Fast Setting Adhesive based on SMX® Hybrid Polymer, supplied in a 600ml Eco-Friendly Foil Pack Cartridge, reducing wastage up to 95% compared to plastic cartridges.
Soudal Fix All Turbo may be applied onto wet and damp surfaces, and is suitable for use internally and externally.
Soudal Fix All Turbo is designed for bonding applications where adhesive build up speed is highly critical or important. Soudal Fix All Turbo also contains a fungicide making it suitable for use in Kitchens and Bathrooms.
Supplied in 600ml Cartridges, available in White colour only.
Soudal Fix All Turbo is a super fast elastomeric adhesive.
Soudal Fix All Turbo has rapid strength build up after 20 minutes and final bond strength after 3 hours, high initial tack.
Soudal Fix All Turbo can be applied in all weather conditions (including wet and damp surfaces), internally and externally. No solvents or odours. Primerless adhesion on most construction materials.
Super Fast
Supplied in 600ml Environmentally Friendly Foil-Pack Cartridge
Up to 95% LESS Wastage when using Foil Cartridges, easily disposable
Rapid strength build up after 20 minutes
3 hours final bond strength
Virtually Odourless
All Weather Use
Primerless adhesion
For all elastomeric bonding applications where adhesive build up speed is highly critical or important.
Heavy duty bonding in all weather conditions, on most surfaces.
Bonding and sealing of porous natural stone surfaces such as marble and limestone.
Porous surfaces in water loaded applications should be primed with Soudal Primer 150.
Smooth surfaces should be degreased before bonding them together. We recommend a preliminary adhesion test on every surface.
Fix-All Turbo has been tested on the following metal surfaces: Steel, AlMgSi1, brass, electrolytic galvanised steel, AlCuMg1, flame galvanised steel, AlMg3 and steel ST1403.
Fix-All Turbo also has a good adhesion on plastics: Polystyrene, polycarbonate (Makrolon®), PVC, ABS, polyamide, PMMA, fiberglass reinforced epoxy, polyester.
While producing plastics very often releasing agents, processing aids and other protective agents (like protection foil) are used. These should be removed prior to bonding.
NOTE: Bonding plastics like PMMA (e.g. Plexi® glass), polycarbonate (e.g. Makrolon® or Lexan®) in stress loaded applications can give rise to stress cracking and crazing in these substrates. The use of Fix All Turbo is not recommended in these applications.
There is no adhesion on PE, PP, PTFE (Teflon®) and bituminous substrates. We recommend a preliminary compatibility test.
Application: Apply the adhesive using the Soudal Manual Foil Pack Applicator in uniform adhesive strips or dots (every 15 cm) on one of the substrates. Always apply an adhesive dot or strip on the corner and edges of panels. Bond the substrate and tamp with a rubber hammer. If necessary, support the bonded materials. The adhesive is hand tight after 20min and can be loaded after 3 hours.
Cleaning: With Sealant Remover immediately after use. Cured Fix-All can only be removed mechanically.
Finishing: Spray with a Soapy Solution before skinning. Tool with Soudaglatt Smoothing Tool, if using product as a sealant.
Repair: With the same material
Fix-All Turbo is paintable with most Water-based paints, however due to the large number of paints and varnishes available we strongly suggest a compatibility test before application.
The drying time of alkyd resin based paints may increase.
Fix-All Turbo can not be used as a glazing sealant.
Not suitable for bonding aquariums.
Fix-All Turbo can be used for bonding of natural stone, but it cannot be used as a joint sealant on this type of surface. Fix-All Turbo can therefore only be used on the bottom of natural stone tiles.
When applying, make sure not to spill any sealant on the surface of materials.
White
We've added to your cart