Tanking Slurry System

Platinum Chemicals offer various basement tanking slurry products. Here you will find a range of cementitious Tanking slurry including:   Platinum Tanking Slurry and HydraDRY (BBA Approved) Tanking Slurry, both of which are designed for application to the internal surfaces of walls and the associated solid floors of cellars, basements and other areas below ground level and subject to penetrating dampness. Platinum Fillet... Read More

Tanking Slurry System

HydraDry Tanking Slurry
Quick Look

HydraDry Tanking Slurry

£28.25 ex. VAT | £33.90 inc. VAT

HydraDry Tanking Slurry

Free Delivery Always get free delivery when purchasing this product | Find out more...

HydraDry Tanking Slurry

Wykamol Group | Basement Tanking

Basement Tanking & Internal Waterproofing Penetrating Damp

IMPORTANT: HYDRADRY IS NOW SUPPLIED IN 20KG BAGS. A 20KG BAG WILL MIX WITH 5.2L OF WATER (RATHER THAN 6.5L, AS IT WAS WITH A 25KG BAG PREVIOUSLY).

HydraDry is a cementitious Tanking Slurry designed for application to the internal surfaces of walls and the associated solid floors of cellars, basements and other areas below ground level and subject to penetrating dampness.

The HydraDRY system prevents ingress of liquid water and works by forming a physical and chemical bond with the substrate. It provides a monolithic waterproof membrane yet still allows some vapour transmission thereby reducing the risk of condensation.

HydraDRY can provide sufficient protection of a ‘Grade 3’ basement as defined in Table 1 of BS8102:2009 and conforms with Category 7 of the BCA Basement Waterproofing Design and site guides.

 HydraDRY is supported by BBA Certification Certificate No: 02/3961.

Available in 20Kg bags (Inside a mixing bucket). 

Advantages
  • BBA Approved

  • Waterproofs cellars and basements.

  • Suitable for brick, stone, block, concrete, etc.

  • Resists hydrostatic pressure up to 5 metres head

  • Can be applied to saturated surfaces

  • Easy brush application

  • Suitable for use in contact with potable water

Preparation

Health & Safety Recommendations:

Take the usual labour hygiene into account.

PPE should be worn during application. See our Safety & PPE Products.

Consult label and material safety data sheet for more information.

Preparation:

It is essential that preparation of the surfaces to be tanked is carried out to a very high standard to ensure that a good physical key is obtained. All fixtures, fittings (e.g. timber wall plugs),plaster or other wall coverings should be removed.

It is strongly recommended that grit blasting is used to prepare the wall surface although where major contamination is present needle guns or “comb” hacking systems (resulting in a rough-textured finish) can be used.

Where necessary defective brickwork should be replaced and poor mortar joints repaired. If the substrate is irregular, e.g. random stone construction, a 3:1 sand / cement scratch coat should be applied to provide a sound, even base prior to the application of HydraDRY.

It is important that good quality sharp, washed sand is used; a waterproofing additive may be included provided the application of HydraDRY is commenced within 48 hours.

N.B. It is essential to determine the suitability of the substrate to accept a cement based coating. All traces of any gypsum-based materials must be completely removed. Where it is known or suspected that high levels of salt contamination i.e. sulphates, nitrates are present in the substrate, mortar joints should be deeply raked out and an SBR-sulphate resisting cement primer and re-pointing mix used prior to the application of HydraDRY. Where the building structure has cracked and / or is subject to subsidence, it should be established whether the movement of ground is still active.

HydraDRY is a relatively rigid material and is not recommended where movement is likely (e.g. under roads, pavements etc.)

Where active water leaks are present it must be established that the structure is capable of taking the increased load which may result from waterproofing work. Alternatively, take measures to reduce the water table. If a few minor leaks exist these should be cut out to leave a square hole in the substrate.The holes can then be filled using Water-Stop Plugging Compound mixed to stiff putty. It is important that Water-Stop is pushed firmly into the hole to ensure that it is totally filled. If severe leaks are experienced pressure vents should be formed by following a similar procedure, but incorporating hollow pipes into the holes, fixed using Water-Stop.

The water can be drained into buckets or directly into the drainage system. HydraDRY is then applied in the normal manner. When the HydraDRY system has cured each vent is carefully removed and the hole plugged with Water-Stop prior to the application of two coats of HydraDRY.

Wall / floor and corner joints usually need special preparation to avoid sharp changes of angle in the tanking membrane.

The joints should be thoroughly raked out, cleaned and wetted prior to application of a Fillet Seal or an SBR / Cement Primer and SBR modified 3:1 sand / cement fillet.

The HydraDRY membrane should be applied the full height of any soil retaining structures and at least 150mm beyond the damp-proof course (if a chemical DPC is being installed this should be a water-based or injection mortar-type system and the HydraDRY applied before DPC reduced suction).

In free-standing basement walls it may be possible to install a horizontal DPC to control capacity moisture movement at or just above floor level, but only if the resting water table height is never above floor level. Similarly, vertical DPC’s (set back approx. 500mm) may be installed in such walls to ‘isolate’ them from soil retaining structures as long as HydraDRY is applied a full 100mm back from the wall / wall joint.

Alternatively, if any doubt exists concerning water table heights, all walls and floors in basements should be tanked.

Where external ground level is above basement ceiling level and of solid masonry construction it will be necessary to treat the ceiling with HydraDRY. Wooden ceilings with joists bearing on walls to be treated with HydraDRY should be isolated and reformed and/or other measures taken to protect the timbers from decay (further advice available on request).

In the majority of tanking operations it is preferable to replace existing concrete floors with a new floor incorporating a damp-proof membrane.

However, if the floor is known to be structurally sound and the surface in good mechanical condition it is possible to use HydraDRY as a DPM followed by the application of a suitable screed.

However, vapour impermeable or moisture sensitive floor coverings such as vinyls or timber flooring should be avoided unless a physical DPM complying with CP102 is used.

Application

Ensure powder is stored at room temperature for a minimum 12 hours prior to use.

During application the temperature of both the substrate and materials must not fall below 5°C.

In winter months avoid using chilled mixing water. Use warm water (20°C) for HydraDRY and Water-Stop.

General:

Immediately prior to application of HydraDRY or backing coats the substrate to be treated should be cleared of all dust etc. and thoroughly wetted with clean water. At the time of application all surfaces must be damp but free of surface water.

HydraDRY powder should be mixed with clean water to a brushable slurry paste consistency (approx. 5.2 litres / 20kg HydraDRY powder). Mixed material should be used within 30 minutes.

HydraDRY should be applied using a stiff bristled brush or broom (wash frequently to avoid clogging). Two coats of HydraDRY should be applied at a thickness of 1.5mm per coat. It is essential that the first coat is brushed well into the surface to ensure a good bond with the substrate. The second coat may be applied as soon as the initial application has dried sufficiently to form a firm base. This will normally be between 2-16 hours depending upon site conditions (allow more time for curing then temperatures fall below 10°C).

Where HydraDRY is applied by towel (reduce gauging water slightly) this must be restricted to the second coat and a “stippled” finish left (use applicator brush) to provide a physical key for subsequent re-plastering.

HydraDRY should not be applied in a thickness greater than 3-4mm (2 coats). Where each application cannot be finished within a single working day it is essential than an overlap of at least 250mm is used to prevent butt joints.

Work should not be stopped at corners or other natural breaks in the construction.

Salts:

If the basement has a known history of aggressive salts specific precaution should be taken to deal with these (the type of salts present should be determined by analysis).

In particular HydraDRY is not suitable for use in areas of high sulphate content (where the sulphate content exceeds Class 3 limits of BRE deposit 363.) It may be possible to impart improved salt resistance to HydraDRY by incorporating an SBR Bonding Agent into the gauging liquid (i.e. 1:1 with water). In other situations an SBR Primer / SBR Render based on sulphate resisting cement may be advisable.

In very severe cases of poor wall stability or acute salting conditions consideration should be given to alternative strategies for achieving a dry wall / floor surface.

Floors:

When a new floor is being laid, the physical membrane should be cut off at the top of the slab and the procedure noted under wall / floor joint followed prior to the laying of the final screed.

Wall / Floor & Corner Joints:

Detailing at the wall floor joint must be carried out to a high standard. Fillet Seal is a cementitous mix designed specifically for the task.

Alternatively two coats of an SBR primer bonding coat are applied (1 part SBR : 2 parts cement by volume).

As soon as possible thereafter a 3:1 sand / cement mix incorporating a good quality sharp washed sand and gauged with SBR : Water (1:1) is used to form a fillet at least 50mm high and 50mm deep at the wall / floor joint.

The fillet is trowel applied taking care not to pierce the SBR primer coat. The edges of the fillet should be 'feathered' to give a smooth curved appearance (this may be achieved by using a glass bottle).

As soon as the fillet has set firm the application of HydraDRY should proceed (if the SBR modified fillet fully cures a fresh coat of bonding primer will be necessary to re-key the surface).

Where the HydraDRY is not being used over the whole floor area it must extend a minimum 250mm across the floor (the second coat should stop 50mm back from the first). If a sandwich bitumen membrane is being incorporated this may be applied directly to the HydraDRY and screeded in the normal manner.

Bitumen emulsions are unsuitable for these situations.

N.B. If the wall / floor joint is a source of active water leaks cut a square-shaped chase (not a v-notch) at the base of the wall and fill with Water-Stop before proceeding.

Coverage:

Approximately 3kg per square metre per coat (two coats recommended).

Finishing

Re-Plastering:

Re-plastering is an integral part of the tanking specification, protects HydraDRY from impact damage and reduces the incidence of condensation.

Renovating Plaster is particularly recommended as a means to avoid cold surfaces but a sand : cement plaster incorporating RenderProof Waterproofer may also be used.

Re-plastering should be carried out in accordance with BS5492:1990 and the appropriate Replastering Specification Data Sheet as soon as the final HydraDRY coat has set to form a firm base (12-48 hours). If the HydraDRY is left longer prior to re-plastering an SBR-modified cement slurry may be required to overcome low suction in the substrate.

N.B.Gypsum based plasters must not be used in direct contact with HydraDRY.

Use only stainless steel metal angle beads to form details on external corners etc. (use SBR-modified mortar to fix). In hot weather keep the plaster / tanking moist (e.g. mist spraying, polythene sheet) over the first 48-72 hours to encourage full curing and strength development.

Reinstatement:

The success of any tanking system depends upon the integrity of the system being maintained. Therefore, conventional fixing methods, i.e. screws etc. cannot be used and alternative fixing methods have to be employed.

For lightweight fixings it is suggested that adhesives are used to stick items such as skirting boards, electrical conduit etc. A wide range of products are available for this purpose, e.g. polyurethane mastic’s.

For heavy duty fixing points, before application of HydraDRY, oversized holes should be drilled. These can then be plugged with Water-Stop and a plastic insert.

For major fixings a larger size hole should be prepared, i.e. a half brick and the same basic procedure followed.

In exceptional circumstances heavy duty fixings may be made after the completion of the HydraDRY system by using chemical anchor systems. i.e. epoxy mortars, two-pack resin systems, but this is not recommended.

Decoration:

On completion of the HydraDRY system it is important that the system is allowed to dry out naturally without the use of radiant or fan heaters, dehumidifiers or forced ventilation (convector heaters to provide temperatures above 10°C may be acceptable).

Once the surface is substantially dry, paint or other finishes may be applied, it is essential that all decoration is vapour permeable and it is suggested that an emulsion paint is used.

In tanked basements the provision of adequate background heating and ventilation is essential to ensure condensation risks are controlled.

Data Sheets

Technical Data Sheet

Safety Data Sheet

BBA Certificate

£28.25 ex. VAT | £33.90 inc. VAT

Water Stop - Fast Set Plugging Mortar
Quick Look

Water Stop - Fast Set Plugging Mortar

£14.50 ex. VAT | £17.40 inc. VAT

Water Stop - Fast Set Plugging Mortar

Water Stop - Fast Set Plugging Mortar

Wykamol Group | Basement Tanking

Basement Tanking & Internal Waterproofing Penetrating Damp

Water Stop (Formerly named HydraPLUG) is a fast setting, expanding water stop plugging and repair mortar.

When mixed with clean water and applied correctly it is formulated for the rapid patching and plugging of active water leaks and seepage in concrete and masonry.

Water Stop is designed to expand as it sets to ensure a permanent water tight seal is achieved and in a cured formed displays similar properties to concrete.

Water Stop is use to stop active water leaks or seepage under pressure through holes, joints and cracks in concrete or masonry walls, swimming pools, water storage facilities, tunnels, fountains, cisterns, water channels, ponds, pipes, basements, foundations and retaining walls.

Water Stop is also ideal for used for rapid anchoring of bolts, conduits, pipes, sanitary equipment, etc.

Available in 5Kg Buckets (2 x 2.5Kg Packs in each Bucket).

Advantages
  • Instantly Stops Leaks in Concrete & Masonry

  • Provides a Permanent Watertight Seal

  • Fast Setting and Rapid Curing

  • Resists Positive & Negative Water Pressure

  • Suitable for use Above & Below Ground

  • Suitable for Internal and External use

  • Safe to use in contact with Potable Water

Preparation

Substrate Preparation:

All areas to be repaired and plugged should be free from mildew, dirt, dust and any loose material.

Clean the hole, crack or joint thoroughly by wire brushing, chiselling or scraping loose materials until a clean, sound substrate remains.

Areas to be patched should be cut back and given a good mechanical key. Feather edges are not allowed.

For dry repair applications, wet the repair area with water leaving it surface saturated dry (SSD) during the repair.

To seal leaks and cracks openings must be chased out to approx 20 mm square. The edges must be square or under cut, avoiding V-shaped cuts. All loose material and debris should be removed.

Application

Mixing:

Due to the fast setting nature of Water Stop, it is important to organise the work space before mixing commences. Ensure the person undertaking the repair is situated close to the repair area and required equipment to carry out the repair is present.

To achieve a 'stiff' mortar, the recommended water addition is 200ml - 220ml of clean water per 1Kg of Water Stop.

For best results the temperature of the mixing water should be between 15°C and 25°C.

Wearing suitable gloves, mixing is ideally done by hand.

  1. Add the recommended water addition into the bucket.

  2. Add the powder to the water and mix quickly and thoroughly.

  3. Roll the mixture between your hands until the material starts become warm and a pliable, putty like consistency is developed.

  4. Immediately use Water Stop.

Important: Mix only enough material for immediate use as Water Stop sets in 2 - 4 minutes and cannot be reworked once it has set.

No priming is required but for dry repair applications, make sure the surface is Surface Saturated Dry (SSD).

Application:

To stop surface leaks or seepage not under pressure:

  1. Starting at the top of the hole or crack, work your way down. Trowel apply or hand kneed the mixed mortar firmly into place, ensuring maximum contact with the substrate before the material sets.

  2. Remove any excess material to form a uniform surface.

To stop leaks under pressure or under water:

  1. Starting at the top of the hole or crack, work your way down. Trowel apply or hand kneed the mixed mortar firmly into place, ensuring maximum contact with the substrate before the material sets.

  2. Maintain constant pressure on the applied material until final set has been achieved.

  3. Remove any excess material to form a uniform surface.

Conditions & Limitations:

Water Stop can be used in cold conditions down to 1°C.

It is advised to use warm water, 20°C to accelerate strength development.

The material should not be applied when substrate and / or ambient air temperature is less than 1°C.

Set and cure times will be increased at low temperatures.

When using Water Stop in temperatures above 35°C, the material should be stored in the shade and it is advised to use cooler water, around 20°C.

Set and cure times will be reduced in hot temperatures.

Curing:

Final setting time is less than 5 minutes. Once the placed Water Stop has stiffened sufficiently, dampen with clean water and maintain in a damp condition for a minimum of 15 minutes.

Data Sheets

Technical Data Sheet

Safety Data Sheet

£14.50 ex. VAT | £17.40 inc. VAT

Tanking Slurry Block Brush
Quick Look

Tanking Slurry Block Brush

£2.50 ex. VAT | £3.00 inc. VAT

Tanking Slurry Block Brush

Tanking Slurry Block Brush

Platinum Building Chemicals Ltd | Basement Tanking

Basement Tanking & Internal Waterproofing Penetrating Damp

High quality Block Brush used to apply our range of Cementitious Tanking Slurries.

£2.50 ex. VAT | £3.00 inc. VAT

Salt Neutraliser 1, 5 & 25 Litres
Quick Look

Platinum Salt Neutraliser

£5.95 ex. VAT | £7.14 inc. VAT

Platinum Salt Neutraliser

Platinum Salt Neutraliser

Platinum Building Chemicals Ltd | Damp Proofing

Basement Tanking & Internal Waterproofing Rising Damp

Platinum Salt Neutraliser is an aqueous solution that has been specifically developed to overcome the problem of salts in a wide range of substrates from new plasterwork to old stone.

Due to rising dampness, salts contained in ground water are absorbed into the masonry and subsequently into the plaster coat. If the rising damp had been severe the plasterwork can lose key and visual evidence of this problem can often be noted by the presence of salt deposits.

In such severe circumstances the plasterwork must be removed and re-plastering carried out in accordance with an appropriate re-plastering specification which will prevent any residual salts in the base substrate migrating into new plasterwork.

There are, however many situations where the type of salts within the masonry are such that the plasterwork remains in good condition. In these cases the Salt Neutraliser can be used thus saving considerable time and expense by not having to re-plaster these areas.

There are many other occasions where even after re-plastering work, salt efflorescence can be seen on the new plasterwork. This often leads to concern that the damp proof course has failed, when in fact, in them, majority of cases the efflorescence is due to other factors such as drying out, salts in construction, plumbing or rainwater leaks, condensation or salty bricks. Under these circumstances Salt Neutraliser is an ideal product to treat the problem.

NOTE: FOR INTERNAL USE ONLY. THIS PRODUCT IS NOT RECOMMENDED FOR EXTERNAL SALTING PROBLEMS.

Available in 1 Litre, 5 Litre and 25 Litre Containers.

Advantages

Salt Neutraliser

  • Neutralises the action of salts to prevent or reduce efflorescence.

  • Applicable to all internal mineral building surfaces.

  • Used as concentrate or in diluted form.

Application

Directions For Use:

  1. Brush away or remove all loose salts.

  2. Thoroughly soak the affected area with clean tap water.

  3. Apply Salt Neutraliser by brush or roller to areas showing salts contamination. Under most circumstances one coat or application will be adequate.
    a) Where heavy salting on old brickwork is being treated use Salt Neutraliser as the concentrate (container strength).
    b) On new plasterwork or light salting use Salt Neutraliser diluted with water up to 50/50 dilution rate.

  4. Some frothing may occur which is due to the reaction with the salts. Allow some time for the neutralising action to be completed. A white deposit may be left on the surface where original efflorescing has taken place and is sometimes difficult to remove.

  5. If re-decorating is to be applied on the treated surface the area should be washed with water and allowed to dry. Do not redecorate at any time until the treated areas are thoroughly dry.

Coverage:

Coverage will vary with the type of surface and substrate: 1 litre concentrate should treat 5m² to 10m².

Data Sheets

Technical Data Sheet

Safety Data Sheet

£5.95 ex. VAT | £7.14 inc. VAT

SBR Bonding Agent
Quick Look

SBR Bonding Agent

£12.75 ex. VAT | £15.30 inc. VAT

SBR Bonding Agent

SBR Bonding Agent

Wykamol Group | Basement Tanking

Basement Tanking & Internal Waterproofing

SBR Latex is a Styrene Butadiene Copolymer Latex which is specially modified to be compatible with cement based mixes (ordinary portland cement or high aluminium cement).

It may be incorporated into cementitious renders, screeds or patching mixes in order to improve adhesion and abrasion resistance.

It can be used internally or externally and in areas of continuous or intermittent water contact.

SBR Latex improves the chemical and water resistance of cementitious mixes and is recommended for use in effluent tanks, dairies, food factories, fertiliser stores etc.

When used in a cementitious mix, SBR Latex has the following special properties:

  • Suitable for use in damp conditions

  • Imparts high water / salt resistance when incorporated in a mix

  • Improves adhesion

  • Allows thinner screeds to be laid

  • Improves workability

  • Allows a reduction in water content

  • Improves flexibility and reduces cracking

  • Improves resistance to abrasion and chemicals

Available in 5 Litre & 25 Litre Containers

Preparation

Where specific building methods are covered by British Standard Codes of Practice, ie. rendering and floor screeds, these should be followed as a guide to good building practice.

All surfaces must be sound and free from laitience, paint, grease, oil, surface water or any other contaminant which may adversely affect adhesion. Surfaces of high suction should be thoroughly dampened before the application of bonding primers.

Remove excess water from the surface before continuing. The sand to be used in the mixes should be well graded, clean and meet the appropriate British Standards.

Applications

NOTE: In relation to 'Bonding Primers' and 'Mix Designs', please view 'APPENDIX' tab.

Application 1 - Patching:

Additional preparation is required where steel reinforcement is exposed.

Wire brush or preferably grit blast to remove rust and scale, apply 'Bonding Primer 2' liberally by brush to the prepared exposed steel and allow to become firm.

Dampen the surrounding substrate and apply 'Bonding Primer 2' over the entire area to be patched.

Finishing: Whilst the final Bonding Primer coat is still wet / green, patch onto the Bonding Primer using 'Mix 1'.

Application 2 - Bedding:

Bonding Primer: Apply 'Bonding Primer 1' by brush to both the prepared surfaces.

Finishing: Whilst the Bonding Primer mix is still wet / green, butter one of the surfaces with 'Mix 1'.

Provide temporary support where necessary.

Note: For thin joints use fine graded sands (BS1199; ‘Type B’), keeping the water content to the minimum.

Application 3 - Pointing:

Bonding Primer: Apply 'Bonding Primer 1' into the dampened joints. Prime only small areas which can be jointed easily before the primer dries or sets.

Finishing: Whilst the Bonding Primer is still wet / green, point the joints with 'Mix 1'.

Application 4 - Waterproof Renders:

Bonding Primer: Apply 'Bonding Primer 1' by brush to the dampened surface.

For difficult surfaces, i.e. weak and porous substrates, apply a coat of 'Bonding Primer 2' brushing vigorously into the surface, stippling to provide a key.

Allow to harden (minimum 16 hours, maximum 3 days), then apply one coat of 'Bonding Primer 1' by brush onto the dry primer coat, again stippling to provide a key.

Finishing: Whilst the Bonding Primer is still wet / green, apply a render of 'Mix 1' to a minimum thickness of 6mm. Lightly scratch to provide a key and apply a second coat of 'Mix 1', maximum 6mm thick, when the first coat is firm (approx. 6 hours).

Prevent the rendering from drying out during the first 48 hours, eg. by mist spraying with water when firm.

Application 5 - Tanking (Cellars, Swimming Pools and Ponds):

For new construction or existing sound structures eg. dense concrete, engineering bricks etc., (minimum compressive strengths 40 N/mm²).

Additional Preparation: Rake out all unsound joints and re-point as detailed under ‘Application 3 - Pointing’. Allow to cure for a minimum 24 hours before continuing.

Bonding Primer and Finishing: Apply 'Bonding Primer 2', brushing vigorously into the dampened surface, stippling to provide a physical key.

Bed a fillet of 'Mix 1' at the wall and floor junction, whilst the Bonding Primer is still wet/green.

Allow to harden (minimum 16 hours, maximum 3 days) then apply a second coat of 'Bonding Primer 2', by brush, to the dry first coat, laying off at right angles to previous coat, again stippling to provide a physical key.

Apply 'Mix 1' as detailed under ‘Application 4 - Waterproof Renders’.

For areas subject to a high level of water pressure, i.e cellars, basements etc., or where walls / floors are in poor condition, BS 8102:1990 (The Code of Practice for Protection of Structures Against Water from the Ground) should be consulted.

Application 6 - Flooring:

Bonding Primer: Apply one coat of 'Bonding Primer 1'. If the surface is porous, 'Bonding Primer 2' should be used.

Finishing:

  • Screeds 6 - 12mm thickness: Use 'Mix 2'
  • Screeds 12 - 25mm thickness: Use 'Mix 3'
  • Screeds over 25mm thickness: Use 'Mix 3' with SBR Latex reduced to 5 litres / 50 kg cement (ca. 1 part SBR: 3 parts water).
  • Heavy Duty Screeds 12 - 25mm thickness: Use 'Mix 4'
  • Heavy Duty Screeds over 25 mm thickness: Use 'Mix 4' with SBR Latex reduced to 5 litres / 50 kg cement (ca. 1 part SBR: 3 parts water).

The above screeds should be applied whilst the bonding primer is still wet / green. For dense water resistant concrete, 'Mix 5' should be used.

Note: All mixes should be covered with polythene sheeting, damp hessian or mist sprayed for the first 48 hours.

All screeds should be laid in bays not exceeding 25m². The maximum length of the bay should be no greater than 1.5 x the width.

Best results are achieved if work is carried out at temperatures between 5°C and 25°C with the use of well graded, clean, dry sharp sands.

Application 7 - Bonding Gypsum Plaster:

Bonding Primer: Brush apply 2 coats of 'Bonding Primer 3'. Allow approximately 30 minutes between coats.

Finishing: Whilst the second coat of Bonding Primer is still wet, apply gypsum bonding plaster as per normal plastering practice.

Application 8 - Suction Control:

SBR Latex may also be used as a primer coat when diluted with 4 parts water to control suction on very porous and difficult surfaces before subsequent treatments are carried out with cement / gypsum based systems.

AFTER APPLICATION, LEAVE TO DRY THOROUGHLY BEFORE CONTINUING.

Appendix

Bonding Primers:

Bonding Primer 1: 1 part SBR Latex: 1 part water: 5 parts cement (by volume) mixed to produce a smooth, creamy consistency. 5 litres of SBR Latex Liquid would provide enough 'Bonding Primer 1' to cover approximately 30m² per coat.

Bonding Primer 2: 1 part SBR Latex: 2 parts cement (by volume) mixed to produce a thin, smooth cream. 5 litres of SBR Latex Liquid would provide enough 'Bonding Primer 2' to cover approximately 20m² per coat.

Bonding Primer 3: 1 part SBR Latex : 1 part water: 3½ parts gypsum plaster (by volume). Mix to a smooth consistency. 5 litres of SBR Latex Liquid will provide enough 'Bonding Primer 3' to cover approximately 25m² per coat.

Note: All Bonding Primers should be applied to a minimum thickness of 1mm.

Mix Designs:

Note: If using a Mobile Device, the tables below are best viewed in Horizontal mode.

Mix 1:

A OR B
Cement - 50kg
Sand - 125kg
SBR - 15 Litres
Cement - 1 Part by Volume
Sand - 2 Parts by Volume
SBR / Water - @ 3:1 (as Required)
Approximate Mix Volume = 0.1m³ (16m² at 6mm thickness) per 50kg cement

 

Mix 2:

A OR B
Cement - 50kg
Sand - 125kg
SBR - 10 Litres
Cement - 1 Part by Volume
Sand - 2 Parts by Volume
SBR / Water - @ 1:1 (as Required)
Approximate Mix Volume = 0.1m³ (8m² at 12mm thickness) per 50kg cement

 

Mix 3:

A OR B
Cement - 50kg
Sand - 150kg
SBR - 10 Litres
Cement - 1 Part by Volume
Sand - 2½ Parts by Volume
SBR / Water - @ 1:1 (as Required)
Approximate Mix Volume = 0.11m³ (9m² at 12mm thickness) per 50kg cement

 

Mix 4:

A OR B
Cement - 50kg
Sand - 75kg
Granite Chips
SBR - 10 Litres
Cement - 1 Part by Volume
Sand - 1¼ Parts by Volume
Granite Chips - 1¼ (3-6mm) - 75Kg Part Volume
SBR / Water - @ 1:1 (as Required)
Approximate Mix Volume = 0.11m³ (9m² at 12mm thickness) per 50kg cement

 

Mix 5:

A OR B
Cement - 50kg
Sand - 75kg
20mm Aggregate
SBR - 5 Litres
Cement - 1 Part by Volume
Sand - 1 Part by Volume
20mm Aggregate - 2½ Parts - 125Kg by Volume
SBR / Water - @ 1:3 (as Required)
Approximate Mix Volume = 0.14m³ per 50kg cement

 

Data Sheets

    Technical Data Sheet

     

    Safety Data Sheet

     

    £12.75 ex. VAT | £15.30 inc. VAT

    Platinum Lime Inhibitor
    Quick Look

    Platinum Lime Inhibitor

    £29.95 ex. VAT | £35.94 inc. VAT

    Platinum Lime Inhibitor

    Platinum Lime Inhibitor

    Platinum Building Chemicals Ltd | Basement Tanking

    Basement Tanking & Internal Waterproofing

    Platinum Lime Inhibitor is specifically formulated for the control of primary and secondary efflorescence in concrete mixes.

    Platinum Lime Inhibitor is applied to concrete surfaces prior to the installation of a 'Type C' Cavity Drain Membrane System to prevent the ‘leaching’ of free lime from the concrete.

    Primarily designed to be used on new concrete structures, Platinum Lime Inhibitor should also be used to treat cut recesses in existing concrete slabs.

    Typical Applications

    Concrete floors newer than 12 months. The whole of the concrete slab or raft as well as the recess formed ready for Drainage Conduits / Channels.

    Walls - 200mm up the wall from the floor, or where a ‘kicker’ has been formed to a concrete wall, apply from the floor up to 200mm above the kicker.

    Concrete floors older than 12 months - The recess cut into the concrete ready for Drainage Conduits / Channels as well as 200mm either side of floor construction or movement joints.

    Underpinned properties require application to 200mm either side of the joints. Dry-packed areas should be sealed with a cement-based tanking product and then the tanking treated with Platinum Lime Inhibitor

    Advantages
    • Prevents limescale build up

    • Seals concrete

    • Solvent and caustic free

    • Easy to use and handle

    • Non-hazardous (on dilution)

    • Compatible with alkaline substrates

    • Long term durability

    • Complies with BS8102:2009

    Preparation

    Clean the surface to be treated, removing any dirt, mould or loose coatings.

    Mould release agents or floor paints should be completely removed.

    The Lime Inhibitor can be applied to damp substrates but cannot be applied to wet substrates.

    Remove all standing water prior to application.

    Application

    Mixing:

    1. Pour 8 Litres of clean water into a large empty bucket or mixing drum.

    2. Empty contents of 1 Litre Lime Inhibitor into the mix, then fill the empty 1 Litre container with clean water to wash the container and empty into the mix to make a 10 litre ready to use solution.

    3. Pour contents into a Spray Applicator.

    Application:

    Moving along the floor from one end to the next apply an even single coat using a coarse spray.

    Avoid using a fine mist and avoid ponding of the liquid on the surface.

    Coverage:

    Coverage will mainly depend on the porosity of the surface. 10 litres will cover a maximum of 100m²

    Data Sheets

    Technical Data Sheet

    Safety Data Sheet

    £29.95 ex. VAT | £35.94 inc. VAT

    MicroSealer - Concrete Sealer & Lime Inhibitor
    Quick Look

    MicroSealer - Concrete Sealer & Lime Inhibitor

    £69.00 ex. VAT | £82.80 inc. VAT

    MicroSealer - Concrete Sealer & Lime Inhibitor

    MicroSealer - Concrete Sealer & Lime Inhibitor

    Wykamol Group | Basement Tanking

    Basement Tanking & Internal Waterproofing

    MicroSealer is a highly penetrative solution specially formulated to react with hydrated cement both at the surface and to a depth of up to 15mm.

    The Silicate active ingredients form monolithic structures within the concrete which are long-lasting and durable and will improve surface wear characteristics.

    Additionally, a silicone resin component cures to form water repellent properties in the concrete thereby improving even further the resistance to surface water absorption and / or lime efflorescence.

    New concrete floors may be treated after a period of curing (approx. 14 days). However, power-floated floors are not suitable for treatment.

    Please note that MicroSealer will not prevent excessive laitance from delaminating.

    Surface preparation to remove excessively weak material by mechanical abrasion is essential.

    It is also advised that surface weakness in floors with a deficiency in cement content may not be successfully treated by chemical hardening nor is MicroSealer suitable as a surface preparation prior to painting.

    Advantages
    • Water-based / odourless

    • Reduces dusting of old and new concrete

    • Inhibits lime efflorescence

    • Extends floor life

    • Reduces penetration of oil/water

    • Easy to use

    Preparation

    Remove surface dirt, grease, oil and other contaminants.

    Open pores by scraping the floor vigorously with a hard broom or wire brush, followed by soft brooming (or vacuum) to remove dust.

    If the floor is wet washed at this stage, leave to dry before treatment.

    Application

    Application:

    Stir MicroSealer thoroughly and pour evenly over the floor surface – a plastic or galvanized metal watering can with a fine rose is suitable.

    Covering capacity will depend on porosity but an average target is 4-6m²/litre per application. Sweep the dressing backwards and forwards to ensure even saturation and satisfy the absorption of the floor. AVOID FORMING PUDDLES.

    Allow to stand for 24 hours between coats. The floor can be used during treatment. The number of coats required will depend on porosity of the floor.

    Applications should continue at 24 hour intervals until the surface is no longer dusting after rubbing (2 -3 coats is normally sufficient). Do not use at temperatures below 5°C.

    NB. It is very important to remove excess MicroSealer from the surface with a sponge or mop ten minutes after application in order to remove any unreacted material from the surface. 24 hours after the final application swill the floor down with clean water and brush well.

    MICROSEALER IS NOT RECOMMENDED FOR USE WITH FLOOR PAINTS.

    Coverage:

    First Coat: 1 litre per 4m² - 6m²

    Subsequent Coats: 1 litre per 6m² - 8m².

    Data Sheets

    Technical Data Sheet

    Safety Data Sheet

    £69.00 ex. VAT | £82.80 inc. VAT