Paving & Patio Products from Platinum Chemicals.
Products within the range include:
A solvent free acrylic coating used to seal and protect patios, paths, natural stone, block paving, concrete to provide a clear hard wearing water repellent film which gives a low sheen slip resistant finish.
A specially formulated concentrated blend of powerful detergents and cleaners for removing surface organic growth, dirt and grime from most surfaces.
Platinum Building Chemicals Ltd | Organic Cleaner
Many walls, roofs, pathways and drives are contaminated by organic growth (lichen, moss etc), dirt and grime especially on north elevations and near trees.
The removal of this organic growth, dirt and grime without affecting the stone, slate, render or brickwork enhances the appearance of the property.
Organic growth on paths, walkways, forecourts and patios causes slippery surfaces which can be a danger to residents, particularly the elderly
Platinum Moss & Algae Cleaner is a specially formulated concentrated blend of powerful detergents and cleaners for removing surface organic growth, dirt and grime from most surfaces.
Supplied in 5 Litre Containers. Concentrated solution, dilutes 1:4 with clean water.
Concentrated Solution - Dulite 1 Part Solution to 4 Parts Water (1:4 Ratio).
Solvent free technology with no volatility issues.
Non-hazardous fully biodegradable surfactants.
No exposure of operators to concentrate.
No deposits or stains on delicate surfaces.
Virtually no odour.
For use on Walking Areas - Paths, Patios, Driveways and Forecourts.
For use on Roofs - Slates, Tiles, Shingles.
For use on Walls - Render, Stone, Brickwork.
For use on Timber - Fencing, Gates, Sheds.
Ensure any debris such as leaves, twigs, loose soil or weeds are removed from surfaces to be treated prior to application.
Dilute 1 part concentrate with 4 parts water.
Apply to surface to be cleaned by watering can or by low volume spray.
Apply in dry conditions at a rate of approximately 3-6 sq metres per litre (this will vary depending on the porosity and condition of the substrate) and leave to take effect.
After applying simply leave for 1 to 3 days and the green growth will slowly disappear (similar to the way weed killers work).
On heavily soiled surfaces a second application may be required.
For extra thick layers of surface contaminants remove by scraping and brushing before application
DO NOT APPLY IF RAIN IS IMMINENT OR EXPECTED WITHIN 6 HOURS.
A 5 litre concentrate, once diluted, will treat up to 150m² depending on the porosity of surfaces being applied to.
Non-Ionic Surfactants: <5%
Cationic Surfactants: <10%
Bond-It | Admixtures & Building Chemicals
Drive Alive Patio Seal is a solvent-free, acrylic liquid used to seal and protect patios, paths, natural stone, concrete and block paving from sunlight, water, oil, petrol and fungal growth.
Drive Alive Patio Seal protects block paving driveways and pathways and patios against water penetration as well as spillages of contaminants, such as oil and grease.
Drive Alive Patio Seal will also deter dirt and grime build-up and will enhance both the present colour of the paths and greatly extend the lifespan of the driveway.
Supplied in 5 Litre Containers, ready to use.
Solvent Free formulation - Low odour.
Facilitates easier cleaning.
Improves water resistance and UV resistance.
Retards mould growth.
Remove organic growth/ lichens, etc. that may be present.
For best results use Platinum Moss & Algae Cleaner prior to application.
Wash all debris away and ensure the surface is dry and free from oil, grease, dust and loose material that may hinder adhesion.
Drive Alive Patio Seal is ready to use, and does not require diluting. We advise that you test this product on a small inconspicuous area prior to use to check compatibility.
Shake well before use and ensure that the surface is completely dry.
Apply a single coat using either a brush, roller or squeegee, ensuring no pooling or ponding occurs. Allow 3-4 hours drying time before trafficking the area.
Application temperature should be between 5°C and 30°C. Colder humid conditions will slow drying times.
Do not apply Drive Alive Patio Seal to wet surfaces or in conditions of high humidity. Do not use when rain is forecast (protect from rain until dry). Do not apply to non-porous surfaces.
Keep children and pets away from treated areas until fully cured.
Do not allow any run off to contaminate drains, waterways or plants.
It is the users responsibility to determine suitability for use.
Areas treated with this product can be cleaned with warm water and detergent or Platinum Moss & Algae Cleaner. Do not use acid based cleaners, as these will remove / discolour the product. Also avoid using power washers.
It is advisable to use this product during warmer/drier months (April - October).
A single coat application will cover approximately 10m²-15m² per litre depending on surface porosity.
Everbuild Building Products | Line Marking Paint
Everbuild Surveyline® is a spray applied solvent-based marking paint for General Contractors / Surveyors spot marking.
Everbuild Surveyline® is colour coded for various uses, it is suitable for highlighting pot holes, machinery positions etc and for general highway maintenance, excavation sites, mining, turf marking and landscaping use.
Everbuild Surveyline® has a semi permanent formula lasts at least 3 months after application under normal wear conditions.
Typically, the following colours have the following applications:
Surveyline® WHITE - General Marker
Surveyline® YELLOW - General Marker
Surveyline® ORANGE - General Marker
Surveyline® RED - Electricity
Surveyline® BLUE - Water
Supplied in 700ml Aerosol cans, in a range of different colours.
High Covering Power.
Semi Permanent Formula.
Adheres to Most Common Surfaces.
Apply by Hand or Applicator.
Highlighting holes, machine positions, fixing positions.
Marking cable positions prior to drilling / cutting.
Turf marking and landscaping use.
Excavation and mining.
Everbuild Surveyline® Paint is designed for inverted use only.
Shake can vigorously for 2-3 minutes after weights are heard to rattle.
To apply by hand remove cap, turn upside down and pull nozzle towards tin using two fingers.
Nozzle must be cleared in any pause during use.
To clear after use, turn can pointing nozzle up and away from user and activate for 1 or 2 seconds.
Do not apply this product if rain is imminent (within 2 hours of application).
As we do not know all the uses the product may be put to, it is the users responsibility to determine suitability for use.
We've added to your cart