Kitchen & Bathroom Silicone Sealants

Soudal Stay Fresh is the ULTIMATE Anti-Mould and Food Safe Silicone Sealant.

Soudal Stay Fresh is a Thick-bodied, 100% Neutral Cure Silicone that contains powerful anti-fungicidal and anti-biocidal agents. It is virtually odourless and has a very fast skinning time and final cure.

Soudal Stay Fresh has primerless adhesion on all sanitary materials, including plastics.

Soudal Stay Fresh is highly elastic and is resistant to UV, rain, snow, ozone and many chemicals. High and low temperature resistant.

Benefits

• Dual Action - Includes a powerful dual action fungicide and biocide, but is safe enough to use in food preparation areas.

• Low Odour - Unlike traditional sealants it does not smell of vinegar, doesn’t contain or release acids and is compatible with all plumbing materials including copper piping.

• Low Emissions - Stay Fresh is classified as a low emission product, rated A+ Indoor Emission Level and EC1plus under GEV-EMICODE.

• Solvent Free - Contains no volatile solvents and does not shrink after use.

• Lifetime Guarantee against Black Mould Growth

Application

Typical Applications:

• For sealing shower bases and cubicles, sealing around baths, wet rooms, sinks, basins and any other sanitaryware.

• For use in kitchens, utility rooms and all areas of high humidity.

• Can be used to seal door and window frames internally in areas subject to high condensation.

Surface Preparation:

Surfaces should be clean, dry, free of dust and grease.

Porous surfaces in water loaded applications should be primed with Soudal Primer 150. No primer needed for non-porous substrates.

There is no adhesion on PE, PP, PTFE (Teflon®) and bituminous substrates. We recommend a preliminary compatibility test.

Application Method:

• Application Method: With a manual or pneumatic caulking gun.

• Cleaning: Clean with a Surface Cleaner immediately after use.

• Finishing: With a soapy solution or Soudal Finishing Solution before skinning.

• Repair: With the same material

Joint Dimensions:

• Minimum Width for Joints: 5 mm

• Maximum Width for Joints: 30 mm

• Minimum Depth for Joints: 5 mm

• Recommendation Sealing Jobs: Joint Width = 2 x Joint Depth.

Remarks:

• Do not use on natural stones like marble, granite etc. as it may cause staining.

• Direct contact with the secondary sealing of insulating glass units (insulation) and the PVB-film of safety glass must be avoided.

• Do not use on polycarbonate. Use Silirub® AL2T instead.

• The sanitary formula should not replace regular cleaning of the joint. Excessive contamination, deposits or soap remainings will stimulate the development of fungi.

Data Sheets

Technical Data Sheet

Declaration of Performance (DoP)

Safety Data Sheet

Soudal Silirub+® S1000 is a Premium Quality Acetoxy Sanitary Grade Silicone Sealant which contains powerful anti-fungal agents to restrict mould growth.

Soudal Silirub+® S1000 is thick-bodied formulation with excellent toolability. Primerless adhesion on many construction materials including glass, ceramics, porcelain, metals and wood.

Soudal Silirub+® S1000 is not suitable for use on PVC.

Soudal Silirub+® S1000 is resistant to weathering, chemicals and high and low temperatures. Gloss type finish on all colours.

Benefits

• Primerless Adhesion on Most Traditional Construction Materials

• Conforms to ISO 11600 F&G 25 LM

• XS1 Fungicide (Strongest Fungicide)

Application

Typical Applications:

• Sealing of Joints in Sanitary Applications such as Bathrooms and Kitchens

• Top Sealing in Glazing.

• Joints in Building Products from Aluminium and Finished Materials.

• Sealing in Refrigerators and Container Construction.

• Sealing in Air Conditioning Systems.

Surface Preparation:

Surfaces should be clean, dry, free of dust and grease.

Porous surfaces in water loaded applications should be primed with Soudal Primer 150. No primer needed for non-porous substrates.

There is no adhesion on PE, PP, PTFE (Teflon®) and bituminous substrates. We recommend a preliminary compatibility test.

Application Method:

• Application Method: With a manual or pneumatic caulking gun.

• Cleaning: Clean with a Surface Cleaner immediately after use.

• Finishing: With a soapy solution or Soudal Finishing Solution before skinning.

• Repair: With the same material

Joint Dimensions:

• Minimum Width for Joints: 5 mm

• Maximum Width for Joints: 30 mm

• Minimum Depth for Joints: 5 mm

• Recommendation Sealing Jobs: Joint Width = 2 x Joint Depth.

Remarks:

• Because of the acid nature, certain metals (eg copper, lead) can be affected.

• Do not use on natural stone such as marble, granite, ... (staining). Use for this application Silirub®+ S8800.

• Direct contact with the secondary sealing of insulating glass units (insulation) and the PVB-film of safety glass must be avoided.

• The sanitary formula should not replace regular cleaning of the joint. Excessive contamination, deposits or soap remainings will stimulate the development of fungi.

• A total absence of UV can cause a colour change of the sealant.

• In an acid environment or in a dark room, white silicone can slightly turn yellow. Under the influence of sunlight it will turn back to its initial colour.

• When finished with a finishing solution or soapy solution, make sure that the surfaces are not touched by this solution. This will cause the sealant not to adhere to that surface. Therefore we recommend to only dip the finishing tool in this solution.

• We strongly recommend not to apply the product in full sunlight as it will dry very fast.

• Do not use in applications where continuous water immersion is possible. Do not use on polycarbonate. Use Silirub® AL2T instead.

Data Sheets

Technical Data Sheet

Declaration of Performance (DoP)

Soudal Silirub+® S8800 is a Premium Quality, Non-Staining, Low Modulus Neutral Cure Silicone Sealant which contains powerful anti-fungal agents to restrict mould growth. Specifically designed for use on Natural Stone (i.e Granite, Marble etc.)

Soudal Silirub+® S8800 is extra thick-bodied with excellent toolability, highly elastic and virtually odourless.

Soudal Silirub+® S8800 has primerless adhesion on all common construction materials and is resistant to UV, rain, snow, ozone and many chemicals. High and low temperature resistance. Gloss type finish on all colours.

Benefits & Features

• Low Modulus Neutral Cure Silicone

• No Staining on Porous Surfaces (i.e Marble, Granite and Other Natural Stones)

• Very Easy to Apply

• No Filamenting - Can be Shaped and Finished very well

• Colourfast and UV Resistant

• Weatherproof

• Permanently Elastic After Curing

• Corrosion Free

• Impervious to Mould - Contains ZnP (Biocide with Fungicidal Action)

• Excellent Adhesion on Glass, Ceramic, Enamel and Galvanised Metals

• 25% Maximum Allowed Distortion

• Solvent, Halogen, Acid and Isocyanate Free.

• Resistant Against Usual Household Cleaners and Disinfectants

• Conforms to ISO 11600 F&G 25 LM

Staining Effects on Natural Stone:

Silicone Sealants are made from several raw materials of which Silicone Polymer and Silicone Oil are the two major components.

When a standard silicone is used on Natural Stone, the silicone oil will be released into the Natural Stone causing permanent migratory staining and damage to the stone.

With a specialist Natural Stone compatible silicone (such as this product), the silicone oil is integrated within the polymer, which means it cannot migrate into the stone.

Only Specialist non-staining sealants can be used on Natural Stone without the risk of expensive, long-term damage to the surface.

'Silirub+® S8800' is a Specialist Stone Sealant, and as such is guaranteed not to cause staining.

Application

Typical Applications:

• Sealing of Joints in all Sanitary Applications such as Bathrooms and Kitchens

• Sealing of Expansion Joints in Construction.

• Sealing of Natural Stone Cladding Façades.

• Sealing in Areas Prone to High Humidity

Surface Preparation:

Surfaces should be clean, dry, free of dust and grease.

Porous surfaces in water loaded applications should be primed with Soudal Primer 150. No primer needed for non-porous substrates.

There is no adhesion on PE, PP, PTFE (Teflon®) and bituminous substrates. We recommend a preliminary compatibility test.

Application Method:

• Application Method: With a manual or pneumatic caulking gun.

• Cleaning: Clean with a Surface Cleaner immediately after use.

• Finishing: With a soapy solution or Soudal Finishing Solution before skinning.

• Repair: With the same material

Joint Dimensions:

• Minimum Width for Joints: 5 mm

• Maximum Width for Joints: 30 mm

• Minimum Depth for Joints: 5 mm

• Recommendation Sealing Jobs: Joint Width = 2 x Joint Depth.

Remarks:

• Contact with bitumen, tar or other plasticizer releasing materials such as EPDM, neoprene, butyl, etc. is to be avoided since it can give rise to discolouration and loss of adhesion.

• The sanitary formula should not replace regular cleaning of the joint. Excessive contamination, deposits or soap remainigs will stimulate the development of fungi.

• A total absence of UV can cause a colour change of the sealant.

• In an acid environment or in a dark room, white silicone can slightly turn yellow. Under the influence of sunlight it will turn back to its initial colour.

• When finished with a finishing solution or soapy solution, make sure that the surfaces are not touched by this solution. This will cause the sealant not to adhere to that surface. Therefore we recommend to only dip the finishing tool in this solution.

• We strongly recommend not to apply the product in full sunlight as it will dry very fast.

• Do not use in applications where continuous water immersion is possible.

• Do not use on polycarbonate. Use Silirub® AL2T instead.

Colour Options

Data Sheets

Technical Data Sheet

Declaration of Performance (DoP)

Soudal Silirub® 2/S is a Food Safe, Premium Quality Low Modulus 100% Pure Neutral Cure Sanitary Silicone Sealant. Ideal for use in Kitchens & Bathrooms.

Soudal Silirub® 2/S contains a powerful anti-fungicidal agent and is virtually odourless. Very fast skinning time and final cure. Thick-bodied. Primerless adhesion on all sanitary materials, including plastics.

Soudal Silirub® 2/S is highly elastic and resistant to UV, rain, snow, ozone and many chemicals.

Benefits & Features

Benefits:

• 100% Pure Silicone

• Food Safe

• Long open time.

• Excellent moisture and mould resistance.

• Impervious to mould, contains ZnP (biocide with fungicidal action)

• Very easy to apply

• Colourfast and UV resistant

• Permanent elastic after curing

• Very good adhesion on many materials

• Low Modulus

• Corrosion free

Standards:

• IBE-BVI Direct Food Contact Report CFP-13.009C

• Report IANESCO 3812-food label for applications in food surroundings.

• Report IANESCO 551, conformity to FDA CFR 21 §177.2600 (e)

Areas for Use

Soudal Silirub® 2/S is used for sealing Sanitary, Construction and Industrial applications where food contact is required.

Soudal Silirub® 2/S can also be used for the sealing of containers, cold-storage, air-conditioning, bathrooms, kitchens and other areas prone to high humidity.

Surface Preparation:

Surfaces should be clean, dry, free of dust and grease.

Porous surfaces in water loaded applications should be primed with Soudal Primer 150. No primer needed for non-porous substrates.

There is no adhesion on PE, PP, PTFE (Teflon®) and bituminous substrates. We recommend a preliminary compatibility test.

Application Method:

• Application Method: With a manual or pneumatic caulking gun.

• Cleaning: Clean with a Surface Cleaner immediately after use.

• Finishing: With a soapy solution or Soudal Finishing Solution before skinning.

• Repair: With the same material

Joint Dimensions:

• Minimum Width for Joints: 5 mm

• Maximum Width for Joints: 30 mm

• Minimum Depth for Joints: 5 mm

• Recommendation Sealing Jobs: Joint Width = 2 x Joint Depth.

Remarks:

• Do not use on natural stones like marble, granite etc. as it may cause staining.

• Do not use on polycarbonate. Use Silirub® AL2T instead.

• The sanitary formula should not replace regular cleaning of the joint. Excessive contamination, deposits or soap remainings will stimulate the development of fungi.

• A total absence of UV can cause a colour change of the sealant.

• In an acid environment or in a dark room, white silicone can slightly turn yellow. Under the influence of sunlight it will turn back to its initial colour.

• We strongly recommend not to apply the product in full sunlight as it will dry very fast.

• When finished with a finishing solution or soapy solution, make sure that the surfaces are not touched by this solution. This will cause the sealant not to adhere to that surface. Therefore we recommend to only dip the finishing tool in this solution.

• Do not use in applications where continuous water immersion is possible.

Data Sheets

Technical Data Sheet

Declaration of Performance (DoP)

Safety Data Sheet

Soudal Silirub® 1 Universal is a Premium Low Modulus Acetoxy, 100% Pure Silicone for use in Sanitary Applications such as Kitchens & Bathrooms.

Soudal Silirub® 1 has very fast skinning and curing with very low dirt pick-up. Solvent Free, no shrinkage during curing.

Soudal Silirub® 1 contains a powerful anti-fungal agent to restrict the growth of mould. Thick bodied formulation for ease of use. Excellent break off and tooling.

Soudal Silirub® 1 has primerless adhesion on many common construction materials including glass, ceramic, porcelain, metals and wood. Resistant to UV, rain, snow, ozone and many chemicals. High movement capability. High and low temperature resistance.

Soudal Silirub® 1 has been independently tested to ISO 11600 F&G 25 LM.

Fungicide conforms to ISO 846 Standard.

Benefits

• 100% Pure Silicone

• Very easy to apply

• Colourfast and UV resistant

• Impervious to mould

• Permanent elastic after curing

• Very good adhesion on many materials

Application

Typical Applications:

• Sanitary, Glazing, Construction and Industrial Applications.

• Sealing in bathrooms and kitchens and other areas prone to high humidity.

• Sealing of all types of sanitary ware including baths, basins, showers, toilets and glazed tile surrounds.

• Perimeter sealing of wooden window & door frames.

• Glass to glass sealing joints.

• Top sealing of traditional glass and aluminium joints.

• Industrial sealing applications; coated metals, anodized aluminium, stainless steel.

• HVAC Ducting, pipework, and drainage joints.

• General maintenance sealing of cars, caravans, mobile homes and boats.

Surface Preparation:

Surfaces should be clean, dry, free of dust and grease.

Porous surfaces in water loaded applications should be primed with Soudal Primer 150. No primer needed for non-porous substrates.

Not suitable for use on PVC.

There is no adhesion on PE, PP, PTFE (Teflon®) and bituminous substrates. We recommend a preliminary compatibility test.

Application Method:

• Application Method: With a manual or pneumatic caulking gun.

• Cleaning: Clean with a Surface Cleaner immediately after use.

• Finishing: With a soapy solution or Soudal Finishing Solution before skinning.

• Repair: With the same material

Joint Dimensions:

• Minimum Width for Joints: 5 mm

• Maximum Width for Joints: 30 mm

• Minimum Depth for Joints: 5 mm

• Recommendation Sealing Jobs: Joint Width = 2 x Joint Depth.

Remarks:

• Because of the acid nature, certain metals (eg copper, lead) can be affected.

• Do not use on natural stone such as marble, granite etc. as it may cause staining.

• Direct contact with the secondary sealing of insulating glass units (insulation) and the PVB-film of safety glass must be avoided.

• The sanitary formula should not replace regular cleaning of the joint. Excessive contamination, deposits or soap remainings will stimulate the development of fungi.

• A total absence of UV can cause a colour change of the sealant. In an acid environment or in a dark room, white silicone can slightly turn yellow. Under the influence of sunlight it will turn back to its initial colour.

• When finished with a finishing solution or soapy solution, make sure that the surfaces are not touched by this solution. This will cause the sealant not to adhere to that surface. Therefore we recommend to only dip the finishing tool in this solution.

• We strongly recommend not to apply the product in full sunlight as it will dry very fast.

• Do not use in applications where continuous water immersion is possible.

• Do not use on polycarbonate. Use Silirub® AL2T instead.

Data Sheets

Technical Data Sheet

Declaration of Performance (DoP)

Safety Data Sheet

Soudal Silirub® S is a High Quality Sanitary Grade Acetoxy Silicone sealant which contains a biocide (DCOIT) to help prevent mould growth in areas prone to high humidity such as kitchens and bathrooms.

Soudal Silirub® S has primerless adhesion on many common construction materials such as glass, ceramic, porcelain, metals and wood.

Soudal Silirub® S is resistant to weathering, chemicals and high and low temperatures.

Benefits

• Very easy to apply

• Colourfast and UV resistant

• Impervious to mould

• Permanent elastic after curing

• Very good adhesion on many materials

Application

Areas for Use:

• Sanitary, Construction or Industrial applications.

• Sealing in areas prone to high humidity - kitchens and bathrooms.

• Sealing of all traditional sanitary ware including baths, showers, toilets, basins and glazed tile surrounds.

Surface Preparation:

Surfaces should be clean, dry, free of dust and grease.

Porous surfaces in water loaded applications should be primed with Soudal Primer 150. No primer needed for non-porous substrates.

Not suitable for use on PVC.

There is no adhesion on PE, PP, PTFE (Teflon®) and bituminous substrates. We recommend a preliminary compatibility test.

Application Method:

• Application Method: With a manual or pneumatic caulking gun.

• Cleaning: Clean with a Surface Cleaner immediately after use.

• Finishing: With a soapy solution or Soudal Finishing Solution before skinning.

• Repair: With the same material

Joint Dimensions:

• Minimum Width for Joints: 5 mm

• Maximum Width for Joints: 30 mm

• Minimum Depth for Joints: 5 mm

• Recommendation Sealing Jobs: Joint Width = 2 x Joint Depth.

Remarks:

• Because of the acid nature, certain metals (eg copper, lead) can be affected.

• Do not use on natural stones like marble, granite etc. as it may cause staining.

• Direct contact with the secondary sealing of insulating glass units (insulation) and the PVB-film of safety glass must be avoided.

• The sanitary formula should not replace regular cleaning of the joint. Excessive contamination, deposits or soap remainigs will stimulate the development of fungi.

• A total absence of UV can cause a colour change of the sealant.

• In an acid environment or in a dark room, white silicone can slightly turn yellow. Under the influence of sunlight it will turn back to its initial colour.

• When finished with a finishing solution or soapy solution, make sure that the surfaces are not touched by this solution. This will cause the sealant not to adhere to that surface. Therefore we recommend to only dip the finishing tool in this solution.

• We strongly recommend not to apply the product in full sunlight as it will dry very fast.

• Do not use in applications where continuous water immersion is possible.

• Do not use on polycarbonate. Use Silirub® AL2T instead.

Data Sheets

Technical Data Sheet

Declaration of Performance (DoP)

Safety Data Sheet

Soudal Silirub® A is a General Purpose Low Modulus Acetoxy Cure Silicone Sealant.

Soudal Silirub® A is mould resistant and has primerless adhesion on glass, ceramic, porcelain, metals, stainless steel and wood.

Soudal Silirub® A is suitable for use in Sanitary Applications.

Benefits

• Very easy to apply

• Colourfast and UV resistant

• Impervious to mould, contains DCOIT (biocide with fungicidal action)

• Permanent elastic after curing

• Very good adhesion on many materials

Application

Areas for Use:

• Sanitary, Glazing, Construction and Industrial Applications.

• Sealing in bathrooms and kitchens and other areas prone to high humidity.

• Sealing of all types of sanitary ware including baths, basins, showers, toilets and glazed tile surrounds.

• Perimeter sealing of wooden window & door frames.

• Glass to glass sealing joints.

• Top sealing of traditional glass and aluminium joints.

• Industrial sealing applications; coated metals, anodized aluminium, stainless steel.

• HVAC Ducting, pipework, and drainage joints.

• General maintenance sealing of cars, caravans, mobile homes and boats.

Surface Preparation:

Surfaces should be clean, dry, free of dust and grease.

Porous surfaces in water loaded applications should be primed with Soudal Primer 150. No primer needed for non-porous substrates.

Not suitable for use on PVC.

There is no adhesion on PE, PP, PTFE (Teflon®) and bituminous substrates. We recommend a preliminary compatibility test.

Application Method:

• Application Method: With a manual or pneumatic caulking gun.

• Cleaning: Clean with a Surface Cleaner immediately after use.

• Finishing: With a soapy solution or Soudal Finishing Solution before skinning.

• Repair: With the same material

Joint Dimensions:

• Minimum Width for Joints: 5 mm

• Maximum Width for Joints: 30 mm

• Minimum Depth for Joints: 5 mm

• Recommendation Sealing Jobs: Joint Width = 2 x Joint Depth.

Remarks:

• Because of the acid nature, certain metals (eg copper, lead) can be affected.

• Do not use on natural stones like marble, granite etc. as it may cause staining.

• Direct contact with the secondary sealing of insulating glass units (insulation) and the PVB-film of safety glass must be avoided.

• The sanitary formula should not replace regular cleaning of the joint. Excessive contamination, deposits or soap remainigs will stimulate the development of fungi.

• A total absence of UV can cause a colour change of the sealant.

• In an acid environment or in a dark room, white silicone can slightly turn yellow. Under the influence of sunlight it will turn back to its initial colour.

• When finished with a finishing solution or soapy solution, make sure that the surfaces are not touched by this solution. This will cause the sealant not to adhere to that surface. Therefore we recommend to only dip the finishing tool in this solution.

• We strongly recommend not to apply the product in full sunlight as it will dry very fast.

• Do not use in applications where continuous water immersion is possible.

• Do not use on polycarbonate. Use Silirub® AL2T instead.

Data Sheets

Technical Data Sheet

Declaration of Performance (DoP)

Safety Data Sheet