MCS Mould Eradication Kit

Free Delivery Always get free delivery when purchasing this product | Find out more...

MCS Mould Eradication Kit

Platinum Building Chemicals Ltd | Mould Control

The MCS Mould Eradication Kit is a full multipurpose kit providing the essential products required to held treat and eradicate Black Mould.

  MCS1 Mould Clear Solution carries the HSE Approval No 9453; MCS3 Paint Additive carries the HSE Approval No 7656.


MCS Mould Eradication Kit

The Mould Control System (MCS) is a two stage treatment for walls, ceilings etc. affected by condensation mould. When both stages are completed, surfaces will exhibit excellent resistance to mould growth even under severe condensation conditions.

Typically, full control can be achieved for up to 5 years but this can be extended considerably where moisture control measures are implemented. Platinum Building Chemicals supply a wide variety of condensation control and mould control products to aid with mould eradication and treatment.

The MCS Mould Eradication Kit is supplied with the required Cleaning Solution (MCS1) and Paint Additive (MCS3), along with the recommended PPE equipment (masks, gloves etc.) to treat and clean mould issues in domestic properties.

Kit Contents:

  • 1 x 1 Litre MCS1 (Ready to Use) Mould Clear Solution Spray**

  • 1 x 100ml MCS3 Fungicidal Paint Additive**

  • 1 x Ancona Safety Spectacles (EN166 Approved)

  • 1 x Pair Flock-Lined Green Nitrile Gloves (Chemical & Solvent Resistant)

  • 1 x P2 Fold Flat Valved Respirator

  • 1 x Cleaning Sponge


Active Ingredients:

MCS1 Mould Clear Solution (Ready to Use) - Contains: Acticide 50x 4.76% w/w.

MCS3 Paint Additive - Contains: 3-Iodo-2-Propynyl-n-Butyl Carbamate 14.97% w/w.


Stage 1 - Spray

Spray MCS1 Mould Clear Solution onto the affected surface from a distance of 3-5cm.

Treat visible mould PLUS 1 metre beyond. Repeat the treatment on badly affected areas after 10-15 minutes.

Areas to be Treated:

  • Painted and Timber Areas - Spray the area thoroughly with the MCS1 Mould Clear Solution.

  • Papered Areas - Spray the paper. The MCS1 Mould Clear Solution acts as a biocide and stripping agent. Bag the mould contaminated paper and remove from the property. Treat the exposed plaster with a thorough spraying of MCS1 Mould Clear Solution.

  • General Preparation - Once the surface is dry, scrape off any loose flaking paint and rub down. Previously painted surfaces must be etched using sandpaper.

  • Coverage - The solution should cover approximately 12.5m².

Stage 2 - Wipe

Rub the surface using the sponge provided. Allow approximately 30 minutes for the product to work, then rinse with warm soapy water. Repeat the treatment if necessary.

Stage 3 - Paint Additive

MCS3 Paint Additive is specially formulated to protect decorative finishes from future mould attack. This should be mixed into emulsion paint, primer, undercoat, varnish, gloss, wallpaper paste, textured paint or tile adhesive.

Add 100ml of MCS3 Paint Additive to 5L of water based paint (emulsion, vinyl, silk or matt).

Add 50ml of MCS3 Paint Additive to 5L of solvent based paint (primer, undercoat or gloss).

Blend the Paint Additive for at least 1 minute or until fully dispersed. Apply the paint in accordance with the manufacturers instructions.

Important - Condensation is usually increasingly the main cause of mould. To reduce this underlying problem, ensure adequate ventilation throughout the property. In very extreme cases of mould other remedial measures may be required.

Data Sheets

Technical Data Sheet

More on this product... View Delivery Rates

£23.39 ex. VAT | £28.07 inc. VAT

  • Reviews

  • Customer Reviews

    Based on 1 review Write a review

Related Items

  • £23.39 ex. VAT | £28.07 inc. VAT
  • Delivery Rates

    Delivery To... Under £75 ex. VAT £75 or over ex. VAT
    UK Mainland FREE FREE
    Scottish Islands £29.50 £25.00
    Northern Ireland POA POA
    Isle of Wight £17.00 £12.50
    Republic of Ireland POA POA
    Scilly Isles POA POA
    Isle of Man POA POA