Fix-All® Turbo

Fix-All® Turbo

Soudal | SMX® Hybrid Polymer

Fix-All® Turbo is a super fast elastomeric adhesive.

Fix-All® Turbo has rapid strength build up after 20 minutes and final bond strength after 3 hours, high initial tack.

Fix-All® Turbo can be applied in all weather conditions (including wet and damp surfaces), internally and externally. No solvents or odours. Primerless adhesion on most construction materials.

Benefits
  • Super fast

  • Rapid strength build up after 20 minutes

  • 3 hours final bond strength

  • Virtually Odourless

  • All Weather Use

  • Primerless adhesion

Application

Typical Applications:

  • For all elastomeric bonding applications where adhesive build up speed is highly critical or important.

  • Heavy duty bonding in all weather conditions, on most surfaces.

  • Bonding and sealing of porous natural stone surfaces such as marble and limestone.

Surface Preparation:

Porous surfaces in water loaded applications should be primed with Soudal Primer 150.

Smooth surfaces should be degreased before bonding them together. We recommend a preliminary adhesion test on every surface.

Fix-All® Turbo has been tested on the following metal surfaces: Steel, AlMgSi1, brass, electrolytic galvanised steel, AlCuMg1, flame galvanised steel, AlMg3 and steel ST1403.

Fix-All® Turbo also has a good adhesion on plastics: Polystyrene, polycarbonate (Makrolon®), PVC, ABS, polyamide, PMMA, fiberglass reinforced epoxy, polyester.

While producing plastics very often releasing agents, processing aids and other protective agents (like protection foil) are used. These should be removed prior to bonding.

NOTE: Bonding plastics like PMMA (e.g. Plexi® glass), polycarbonate (e.g. Makrolon® or Lexan®) in stress loaded applications can give rise to stress cracking and crazing in these substrates. The use of Fix All® Turbo is not recommended in these applications.

There is no adhesion on PE, PP, PTFE (Teflon®) and bituminous substrates. We recommend a preliminary compatibility test.

Application Method:

  • Application: Apply the adhesive by means a caulking gun in uniform adhesive strips or dots (every 15 cm) on one of the substrates. Always apply an adhesive dot or strip on the corner and edges of panels. Bond the substrate and tamp with a rubber hammer. If necessary, support the bonded materials. The adhesive is hand tight after 20min and can be loaded after 3 hours.

  • Cleaning: With Sealant Remover immediately after use. Cured Fix-All® can only be removed mechanically.

  • Finishing: With a soapy solution or Soudal Finishing Solution before skinning. 

  • Repair: With the same material

Remarks:

  • Fix-All® Turbo is paintable with most Water-based paints, however due to the large number of paints and varnishes available we strongly suggest a compatibility test before application.

  • The drying time of alkyd resin based paints may increase.

  • Fix-All® Turbo can not be used as a glazing sealant.

  • Not suitable for bonding aquariums.

  • Fix-All® Turbo can be used for bonding of natural stone, but it cannot be used as a joint sealant on this type of surface. Fix-All® Turbo can therefore only be used on the bottom of natural stone tiles.

  • When applying, make sure not to spill any sealant on the surface of materials.

Data Sheets

Technical Data Sheet

Fix-All® Product Selector

Declaration of Performance (DoP)

Safety Data Sheet

More on this product...

£5.75 ex. VAT | £6.90 inc. VAT

  • Reviews

  • Customer Reviews

    Based on 1 review Write a review
  • Reviews

    Customer Reviews

    Based on 1 review Write a review