Borotreat 10P - Boron Powder

Borotreat 10P - Boron Powder

ACS | Woodworm & Dry Rot Treatment

Boron Timber Treatments Woodworm & Dry Rot Treatment

Borotreat 10P is a multipurpose powder concentrate for use as a wood preservative.

In common with other Boron woodworm treatments, it is also a very effective fungicidal against dry rot and wet rot, and will prevent re-infestation.

Borotreat 10P is suitable for all wood that is not in direct contact with the ground or exposed externally.

Borotreat 10P is supplied in convenient pack sizes as 100% w/w Disodium Octaborate Tetrahydrate as the active ingredient.

It is easily diluted with water and provides permanent protection, as the active ingredient does not break down.

For Professional Use Only.

  Borotreat 10P Boron Powder is an HSE Approved product.

Available in 0.5kg and 2.5kg Bag Sizes. Concentrated Powder which dilutes 1:9 with water.

  • 0.5kg Dilutes to make 5 Litres of Ready to Use Solution.
  • 2.5kg Dilutes to make 25 Litres of Ready to Use Solution.
Properties

Product Benefits:

  • Excellent internal preservative for the control of wood rotting fungi and wood destroying insects.

  • Approved under EU Biocides Products Regulations (BPR) for use as a wood preservative.

  • Use Class 1 & 2 – in-situ treatment of internal timber not subject to weather.

  • 1 hour re-entry time.

  • Cost effective, clean and easy to handle.

  • Odourless and non-flammable.

  • Permanent protection as the active ingredient does not break down.

  • Convenient pack sizes.

Active Ingredients:

Disodium Octoborate Tetrahydrate 100% w/w

Preparation

Health & Safety Recommendations:

Take the usual labour hygiene into account.

PPE should be worn during application. See our Safety & PPE Products.

Consult label and material safety data sheet for more information.

Preparation:

All bats are protected under the Wildlife and Countryside Act 1981. Before treating any structure used by bats, consult English Nature (etc).

Before deciding on an appropriate preservative treatment, carefully evaluate the structural integrity of timbers and / or replace those considered unsound (isolating from masonry where possible). Locate and rectify sources of moisture and improve ventilation as appropriate.

Dilute Borotreat 10P Powder 1:9 with clean tap water to give a 10% active working solution. In some cases as a superficial treatment against Dry Rot (Anobium Punctatum) apply a 4% solution at 4m²/litre.

Borotreat 10P is supplied in convenient pack sizes of 0.5kg and 2.5kg bags to make 5 Litres or 25 Litres of diluted product respectively.

Use an oversized bucket or container with the appropriate volume of clean tap water and add the corresponding amount of powder concentrate.

Mix the powder into the water with a suitable paddle during addition and continue until it has completely dissolved. Use warm water if possible to help the powder to dissolve.

The working solution of Borotreat 10P can be applied by brush, spray or injection.

Application
  1. Clean all wooden surfaces using a brush or vacuum cleaner.

  2. Cover electrical installations, water tanks, stored goods and isolate adjacent areas not requiring treatment.

  3. Lift floorboards as required and clean out debris.

  4. Treat all accessible areas with the working solution of Borotreat 10P using brush or spray.

  5. Under normal circumstances one coat will be sufficient but ensure that all accessible wood surfaces are thoroughly wetted out. Any surfaces that absorb solution rapidly should be sprayed again at the time.

  6. Apply a second coat after one to eight hours where there is a severe fungal attack or woodworm infestation.

Note: Borotreat 10P needs to be applied to absorbent timber. Any paint, varnish or stain must be removed prior to application. Polished surfaces must be cleaned back to bare timber.

Bats:

Borotreat 10P can be used to treat bat roosts as a single component product (i.e. no additional active ingredients are used) at the following rates:

Maximum suitable application rate (ml per square metre of timber surface) for products containing single active ingredients.

Concentration of Active Ingredient (%) in Product (Disodium Octoborate Tetrahydrate)
Dilution 0.02 0.05 0.1 0.2 0.4 0.6 0.8 1 5 10 50
Application > 5L >5L >5L >5L 2.8L 1.87L 1.4L 1.12L 225ml 113ml 23ml

Coverage:

By Brush: 1 Litre per 6 - 8m² using a 10% solution.

By Coarse Spray: 1 Litre per 4 - 6 m² using a 10% solution.

By Injection: Apply a 10% solution through 3mm diameter pre-drilled holes.

Data Sheets

Technical Data Sheet

Safety Data Sheet

More on this product...

£11.95 ex. VAT | £14.34 inc. VAT

  • Reviews

Related Items

  • Borotreat 10P - Boron Powder

    Borotreat 10P - Boron Powder

    £11.95 ex. VAT | £14.34 inc. VAT